Bedienungsanleitung Ignis awv 9526 (Seite 2 von 2) (Englisch)

311707

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 512 10069

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 5.0 50* 1.70 2:05

Cotton** 60 5.0 49 0.95 2:10

Cotton 40 5.0 55 0.55 2:00

Synthetics 60 2.5 50* 0.80 1:30

Synthetics 40 2.5 45 0.45 1:15

Delicates 40 1.5 50 0.55 0:45

Quick wash 30 3.0 35 0.40 0:30

Wool 40 1.0 55 0.55 0:45

Handwash 40 1.0 40 0.40 0:35

1. Load the machine, close the drum doors and check

that they are properly locked.

2. Add detergent and additives into the dispenser to

no more than the “MAX” level mark, as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Stain remover agents

• Anti-scale agents (if necessary)

3. Close the lid.

4. Turn the programme selector to the desired

programme and temperature. The lamp next to the

“Start/Pause” button flashes.

CONSUMPTION DATA

Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in

compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to

the water supply pressure and temperature, the load and the type of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water

out.

** Reference Programme for Energy Label.

PREPARATION OF THE WASH CYCLE

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a

wash programme is running, the lid remains locked and

must on no account be forced open. In case you have

an urgent need to open it during a running programme,

refer to “Cancel (Reset) a running programme before

the end”.

RED INDICATIONS

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

Ignis is a registered trademark of Whirlpool USA.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows

the current programme phase, running from left to right

through Wash, Rinse, Spin/Drain. When the programme

phrase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the lid and drum and unload the machine.

4. Leave the lid open for some time to allow the

interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme, any options and another

spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the

end. Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the door can be

opened.

SELECT THE DESIRED OPTION(S)

Selecting or deselecting an option can be done at

any time during the programme. The option will be

applied as long as the corresponding programme

phase has not been executed yet.

“Intensive rinse” button

• The amount of water is increased to ensure a more

intensive rinse.

• This option is particularly suitable for areas with very

soft water, washing baby linen and people with skin

allergies.

“No spin” button

• Especially for delicate garments to avoid wear and

tear caused by the spin.

Note: with the “Cotton” and “Synthetics”

programmes, a short spin cycle is provided in any

case, even if the “No spin” option has been selected,

in order to optimize rinsing results.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ignis awv 9526 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ignis awv 9526

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info