Bedienungsanleitung IHome IP99 (Seite 7 von 14) (Englisch)

110526

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Install/Replace Backup Battery

The iP99 uses a backup battery system to provide continuous alarm operation and clock settings

in the event of a power failure. If the Battery Low Icon located on the right of the display is on, it is

time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise

all settings may be lost during battery replacement.

Open the battery compartment cover located on the bottom of the unit. Insert 2 “AA” batteries

as indicated. We recommend the use of alkaline batteries for longer life.

Batteries information:

•

Do not mix old and new batteries.

•

Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium) batteries.

Replacing iP99 Backup Batteries

Using the iP99

Radio

Setting up Antennas

Snap AM loop antenna into provided stand, then plug AM antenna cable into ƿ AM Loop Antenna socket on back of unit.

Move antenna away from unit for best reception.

Extend ƾ FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas.

c) Locate iP99 and all antennas away from AC adaptor in wall socket (at least 3 feet) for best radio reception.

Tuning and Playing the Radio

Press the ᕥ Radio Button to select radio play mode. Press as needed to select FM or AM radio band.

Turn the Set Wheel to tune radio to a desired station.

To program the current station as a preset, press and hold ᕦ Preset Button 1-2 until P1 flashes on display; press again for P2

and allow to time-out (beep confirmation). Repeat steps a,b,and c for other preset buttons to preset up to 12 stations (6 AM, 6

FM). To listen to a preset station at any time, simply press the desired preset button once or twice.

Turn the ᕤ Volume Wheel to adjust iP99 volume up or down.

e) Press the

ᕨ EQ Button to select Treble, Bass, SRS WOW sound effect or Balance. Turn the Set Wheel to adjust settings. EQ

settings for iPhone/iPod and radio mode are independent.

Press

ᕣ Alarm Reset/Power Button to turn iP99 off.

Using the Line-in Jack

You can play nondocking iPod models or other audio devices through the iP99 ƽ Line-in Jack, connect one end of a patch cord

(available at ihomeaudio.com）in the device’s line out or headphones jack, the other in the iP99 line-in jack. Make sure there

is no iPhone/iPod docked in the iP99 when using the line-in jack.

To listen to your audio device, press the ᕥ Radio Button until “line-in” is displayed, indicating line-in mode. Adjust the output

volume on your line-in device.

Using Sleep Mode

Sleep mode lets you sleep to your iPhone/iPod or the radio, gradually lowering the volume until the unit shuts off at the selected

time.

Press the ᕢ Sleep Button to select an amount of time before the iP99 shuts off: 120, 90, 60, 30 or 15 minutes.

Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting).

Using the Dimmer

a) Press the ᕡ Snooze/Dimmer Button during normal operation to adjust brightness of LCD display. There are 8 levels of brightness

including OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

IHome IP99 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info