Bedienungsanleitung Ikea 904.575.56 Eneby (Seite 5 von 176) (Alle Sprachen)

779266

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

Getting started:

1. Connect mains cord into AC In (2) connector.

2. A quick press on the knob (1) turn the speaker

On. ENEBY 20/30 starts to search for paired

devices. If a paired device is found, the LED

shines without blinking and your speaker is

ready to use.

3. If no device is found the speaker LED continues

to blink and enters pairing mode automatically.

Go to the Bluetooth settings in your mobile

device and connect to ENEBY 20/30. The LED

should now stop blinking and your speaker is

ready to use. If no music has been playing for

20min, the speaker will enter sleep mode.

Adjust Volume

Turn the knob (1) left to decrease or turn it right to

increase volume level.

Add additional Bluetooth device(s)

(max 8 devices)

1. Make sure no other device is paired and in range

to the speaker.

2. Go to your Bluetooth menu on your mobile

device and connect to ENEBY 20/30.

3. Once Bluetooth connection is established, the

white LED stops blinking.

Unpair Bluetooth device

Go to your Bluetooth menu on your mobile device

and unpair ENEBY 20/30 from your devices.

Play music from external source:

Connect a portable audio device to the AUDIO IN (3)

jack on the rear panel. The speaker automatically

detects the external input and disables Bluetooth

functionality. Use a 3.5mm 3-pol Audio cable for

this feature.

Use speaker throughout home:

ENEBY 20 has the possibility to be portable. ENEBY

battery pack is sold separately.

• To insert the battery, open the compartment lid

(5) and insert the battery in the correct direction.

• The battery is charging in the product when

mains cord is connected and the speaker is

turned on.

• When battery is low a red LED in the knob (1) will

ash. During charging the red LED is on.

Attach Speaker to a wall or a stand:

ENEBY wall mount and ENEBY stand are accessories

and are sold separately.

Use holes (4) and included screws to mount stand

or wall mount. Do not over tighten the screws.

Other Settings

Unpair Bluetooth devices Press and hold the knob (1). Release the knob when the LED light turns

red the rst time.

A conrmation sound will be played.

(Note that on some phone models you also need to remove

ENEBY20/30 from the phone’s paired devices list to be able to pair

again.)

Set up a stereo pair You can pair two identical ENEBY speakers to create a wider stereo

experience. In this conguration, one speaker serves as the left

channel and the other serves as the right channel. On/O and Volume

need to be controlled individually on each speaker.

1. Turn on both speakers.

2. Press and hold the knobs (1) at the same time. Release the knobs

when the LED light turns red the second time.

Wait 2 seconds. A conrmation sound will be played.

3. Press the knob (1) once again on one of the speakers.This speaker is

now assigned as the left channel.

4. Open the Bluetooth setting on your mobile device and connect to

ENEBY speaker for the left channel.

To disable the stereo pair, follow instructions “Unpair Bluetooth

devices” on both speakers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ikea 904.575.56 Eneby Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info