Bedienungsanleitung Ikea DATID HGA5K (Seite 3 von 4) (Englisch)

468478

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

INSTALLATION

Technical information for the Installer

If there is no oven beneath the cooktop (any oven installed

must be manufactured by us and equipped with a cooling

system), insert a separator panel at a minimum distance

of 20 mm from the bottom of the cooktop.

Note: before installation, make sure that the local gas

delivery conditions (nature and pressure of gas) are

compatible with the settings of the cooktop, as

indicated on the Product Description Sheet and on the

rating plate.

• The outer surfaces of the furniture or appliances adjacent

to the cooktop must be heat resistant (heat protection

“Y”) according to standards.

• Installation must comply with current local regulations.

• In the room where the cooktop is installed, there must be

enough air to allow the gas to burn correctly

(see the separate Product Description Sheet).

The natural flow of air must take place through an

adequate opening, that must be:

- permanent, made on one of the outside walls of the

room, and communicating with the exterior in an area

away from sources of pollution;

- built so as to ensure that its openings, both on the inside

and on the outside, cannot be obstructed, intentionally or

accidentally;

- protected by a metal grid or mesh that does not reduce

its working section;

- situated near the floor level and positioned so as not to

interfere with the operation of the fume exhaust devices.

- The fume exhaust has to take place through an

appropriate hood or fan installed on the wall or on the

window.

Assembly

Important: the power supply cable and plug must be

suitable for the power absorption of the cooktop, and

the cable must be long enough to permit its upward

extraction.

Electrical connection

• The electrical connections must comply with local

regulations.

• The data relevant to the voltage and power absorption are

indicated on the rating plate.

• The earthing of this appliance is compulsory by law.

• The manufacturer cannot be held responsible for any

injury to persons or animals or damage to property

arising from failure to comply with these

requirements.

• When the cooktop is installed, provide a multi-pole

circuit breaker with a contact separation of at least

3 mm.

• If necessary, the electrical power cable must be

replaced exclusively with a power cable having

identical characteristics to the original supplied by

the manufacturer (type H05V2V2-F - T90°C or type

H05RR-F). This operation must be performed by the

After Sales Service or a qualified electrician.

Connection to gas supply

The gas supply system must comply with local

regulations.

You can find specific local regulations for some countries, in

the separate National Safety Regulations Sheet supplied.

If no information concerning your Country is given, please ask

details to your Installer.

The connection of the cooktop to the gas pipe network or gas

cylinder must be made by means of a rigid copper or steel

pipe with fittings complying with local regulations, or by

means of a continuous-surface stainless steel hose complying

with local regulations. Interpose gasket (B) in the elbow

connection.

The maximum length of the hose is 2 m.

FOR BELGIUM ONLY: It is necessary to replace the elbow

connection (A) on the appliance, with the one supplied.

Important: if a stainless steel hose is used, it must be

installed so as not to touch any mobile part of the

furniture. It must pass through an area where there are

no obstructions and where it is possible to inspect it on

all its length.

After connection to the gas supply, check for leaks with

soapy water.

Attention: Should you experience difficulty in turning

the burners knobs, please contact the After Sales

Service for the replacement of the burner tap.

Earth

(Yellow/Green)

ADJUSTMENT TO DIFFERENT TYPES OF GAS

If a different type of gas to the type shown on the rating plate and

on the orange sticker affixed to the top of the cooktop is used,

the cooktop must be converted to work with the new gas type.

Remove the orange sticker and affix it to the instructions booklet,

which must be retained for the lifetime of the appliance.

1. The gas nozzles must be changed by After Sales Service or

a qualified technician.

Nozzles not supplied with the appliance must be ordered

from After Sales Service.

2. Connect the cooktop to the gas shut-off valve by means

of a pipe suitable for the type of gas used, in compliance

with current local regulations.

3. Adjust the minimum setting of the taps.

Note: when liquid petroleum gas is used (G30/G31), the

minimum gas setting screws must be tightened as far as they will

go.

Replacing the injectors (see table in the enclosed

Product Description Sheet)

1. Remove grids (A).

2. Extract burners (B).

3. Using a socket spanner of the appropriate size (C),

unscrew the injector to be replaced.

4. Replace it with the injector suitable for the new type of

gas.

5. Re-assemble the injector in (D).

6. For models equipped with Triple Crown burner, proceed

as shown on figure.

•Unscrew the injector to be replaced (E).

•Replace it with injector suitable for the new type of gas.

Before installing the cooktop, remember to affix the gas

calibration plate supplied with the injectors in such a way that

it covers the existing information relating to gas calibration

Adjusting minimum gas setting of taps

1. To ensure that the minimum setting is correctly adjusted,

remove knob (F) and proceed as follows:

• tighten (-) to reduce the height of the flame;

• loosen (+) to increase the height of the flame;

The adjustment must be performed with the tap in minimum

gas setting position (small flame) .

Upon completion of adjustment, reseal using sealing wax or

an equivalent material.

2. The primary air of the burners does not need to be

adjusted.

3. After the adjustment of the minimum gas setting, light up

the burners and turn the knobs from max. position

to min. position to check the stability of the flame.

Ikea DATID HGA5K Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ikea DATID HGA5K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info