IT 59
Progr
Fase di
asciugatura
Natural
Dry
Opzioni
disponibili *)
Durata del
progr
(h:min)**)
Consumo
d'
(litri/ciclo)
Consumo
di energia
(kWh/ciclo)
1 Eco
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
3:40 8.7 0.59
2 Automatica
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50-60°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensivo
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
65°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
2:40 17.0 1.30
4 Lavaggio rapido 30’
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50° - -
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
0:30 9.0 0.50
5 Lavaggio rapido e
asciugatura
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:20 10.0 1.10
6 Vetr
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
45°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:40 12.0 1.00
7 Silenzioso
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
3:35 16.5 1.00
8 Antibatterico
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
65°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
-
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:40 12.0 1.30
9 Prelavaggio
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
- -
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
0:10 4.5 0.01
10
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
65° - -
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
0:50 9.5 0.70
La misurazione dei dati per il pr
condizioni di laboratorio secondo quanto pr
europea EN 60436:2019.
Nota per i laboratori di pr
sulle condizioni delle pro
indirizzo: dw_test_support@whirlpool.com
Questi progr
stoviglie.
*) Non è possibile selezionare tutte le op
contemporaneamente.
**) Ad eccezione del progr
altri progr
può dipendere da molti fattori, quali la temper
pressione dell’
la dose di detersivo utilizzata, la quantità e il tipo di carico e
il suo bilanciamento, la selezione di determinate opzioni e la
taratur
1. EC Il programma Eco è indicato per le sto
mediamente sporche; è il pr
termini di consumo combinato di acqua ed energia e viene
usato per valutare la conformità dell’
legislazione UE in materia di progettazione ecocompatibile.
2. AUTO - Per piatti con spor
cibo. Rileva il livello di spor
progr
sporco, sul display compar
ciclo viene aggiornata.
3. INTENSIVO - Programma indicato per sto
sporche, consigliato specialmente per pentole e tegami. Da
non usare per sto
4. LAV - Programma indicato per un carico
ridotto di stoviglie normalmente spor
ottenere un risultato di lavaggio ottimale in un tempo più
bre
5. LA - Stoviglie
normalmente sporche. Ciclo quotidiano; permette di
ottenere risultati di lavaggio e asciugatur
tempo inferiore.
6. CRIST - Progr
sensibili alle alte temperatur
tazze.
7. SILENZIOSO - Adatto al funzionamento nelle ore notturne.
Permette di ottenere risultati di lavaggio e asciugatur
ottimali con una minima emissione sonora.
8. IGIENIZZANTE - Per stoviglie normalmente o molto
sporche, include un lavaggio addizionale antibatterico. Ciclo
utilizzabile per la manutenzione della lavastoviglie.
9. PRE-LA Da utilizzare per sciacquare le sto
lavare successivamente. Questo pr
detersivo.
10. Pr
manutenzione della lavastoviglie; de
con l’
per la manutenzione della lavastoviglie.
Note: Si noti che il ciclo FAST W
leggermente sporchi
Le FUNZIONI possono essere selezionate dir
premendo il tasto corrispondente (veder
COMANDI).
Se una funzione non è compatibile con il progr
selezionato (vedere la T
corrispondente lampeggia 3 volte in rapida successione e
viene emesso un segnale acustico. L
caso abilitata.
