FRANÇAIS 44
Installation
A Si l'appar
un autre, gar
nécessaire, il peut êtr
Brancher l'
Lors de l'installation, le branchement de l'
doit être eectué par un technicien qualié.
Les tuyaux d'
vers la gauche ou la droite dans le but d'
installation.
Assurez-vous que le lave-vaisselle ne plie pas ou n
tuyaux.
Brancher le tuyau d'
• Faire couler l'
• Vissez le tuyau d'
Si le tuyau d'
magasin spécialisé ou un technicien agréé.
La pression d'
le tableau des données techniques - sinon le lave-vaisselle ne
fonctionnera pas bien.
Assurez-vous que le tuyau n
Spécications pour le raccor
Alimentation d' chaud ou froid (max. 60°C)
Arrivée d' 3/4”
Puissance de la pression
d'
Pression
0,05 ÷ 1 MPa (0,5 ÷ 10 bars)
7,25 – 145 psi
T
Brancher le tuyau de sortie d'
Branchez le tuyau de sortie à un conduit de dr
diamètre d'A .
INSTALLATION
ENGLISH
A TTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary , it may be tilted onto
its back.
CONNECTING THE W A TER SUPPL Y
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE W A TER INLET HOSE
• Run the water until it is perfectly clear .
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
T e c h n i c a l Data table - otherwise the dishwasher may be function
properly .
Make sure the hose is not bent or compressed.
SPECIFICA TIONS FOR THE CONNECTION OF THE W A TER
SUPPL Y HOSE:
CONNECTING THE W A TER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A .
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B .
ANTI-FLOODING PROTECTION
Anti-flooding protection. T o ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop , which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
W ARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION) .
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door .
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SER VICE) . Do not use extension ca -
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised T echnical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
u n e v e n , the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly , it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher , stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con -
d e n s a t i o n which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
T o adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. T urn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAP ACITY :
MIN 40 cm
MAX 80 cm
W A TER SUPPL Y cold or hot (max. 60°C)
W A TER INT AKE 3/4”
POWER OF W A TER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAP ACITY 13 standard place-settings
Le raccor
entre 40 et 80 cm du sol ou de la surface où s'
vaisselle. Avant de brancher le tuyau de sortie d'
enlevez le bouchon en plastique B .
Dispositif anti-refoulement
Dispositif anti-refoulement. Pour empêcher la survenue de
refoulement, le lave-vaisselle est muni d'
bloque l'
l'intérieur de l'
Certain modèles sont aussi munis du dispositif de sécurité
supplémentaire Ne
anti-refoulement en cas de ruptur
Le modèle dispose du système de protection d'
Le tuyau d'
des pièces électrique sous tension.
Branchement électrique
A
coupé, il comprend des pièces électrique sous tension.
Avant de brancher la che dans la prise de cour
vous que :
• La prise est mise à la terre et est conforme aux r
en vigueur ;
• La prise peut
INSTALLATION
ENGLISH
A TTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary , it may be tilted onto
its back.
CONNECTING THE W A TER SUPPL Y
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE W A TER INLET HOSE
• Run the water until it is perfectly clear .
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
T e c h n i c a l Data table - otherwise the dishwasher may be function
properly .
Make sure the hose is not bent or compressed.
SPECIFICA TIONS FOR THE CONNECTION OF THE W A TER
SUPPL Y HOSE:
CONNECTING THE W A TER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A .
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B .
ANTI-FLOODING PROTECTION
Anti-flooding protection. T o ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop , which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
W ARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION) .
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door .
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SER VICE) . Do not use extension ca -
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised T echnical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
u n e v e n , the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly , it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher , stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con -
d e n s a t i o n which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
T o adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. T urn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAP ACITY :
MIN 40 cm
MAX 80 cm
W A TER SUPPL Y cold or hot (max. 60°C)
W A TER INT AKE 3/4”
POWER OF W A TER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAP ACITY 13 standard place-settings
résister à la charge maximum de l'
qui est indiquée sur la plaque signalétique située à l'intérieur
de la porte (voir DESCRIPTION DU PRODUIT).
• La tension de l'
les valeurs indiquées sur la plaque signalétique située à
l'intérieur de la.
• La prise est compatible avec la che de l’
Si ce n'
remplacer la che (voir le SERVICE APRÈS-VENTE). N'
rallonge, ni multiprise. Une fois que l'
câble d'
être facilement accessible.
Le câble ne doit pas être plié ou écr
Si le câble d'
au fabricant ou un Centre d'
remplacer pour é
L
règles ne sont pas observées.
Positionnement et nivelage
1. Placez le lave-vaisselle sur un plancher solide et au niveau.
Si le plancher est inégal, les supports avant de l'
peuvent être ajustés pour atteindr
horizontale. Si l'
moins enclin à ce déplacer ou vibrer et fair
fonctionnement.
2. Avant d'
transpar
condensation qui pourrait se former
3. Placez le lave-vaisselle de façon à ce que les panneaux
latéraux ou le panneau arrièr
meubles ou le mur adjacent. Cet appareil peut aussi êtr
encastré sous un comptoir
4. Pour ajuster la hauteur du support arrière, tournez la douille
hexagonale r
l'
une ouverture de 8 mm. T
pour le soulever et dans le sens antihor
Dimensions et capacité:
Largeur 598 mm
La taille 820 mm
Profondeur 555 mm
Capacité 13 couverts standard
