Bedienungsanleitung Iluv i9300 (Seite 9 von 21) (Englisch)

504363

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

OPERATIONAL INSTRUCTIONS

Headphones jack

The headphones PHONES jack (10) is for headphones with a 30- to 600-Ohm impedance, and

equipped with a 3.5mm jack. Use an adapter (sold in electronic outlets) if your headphone has a

dierent plug. The speakers are automatically switched o when the headphones are being used.

AM/FM radio operation

1. Turn the unit on by pressing

the POWER button (1)/(34).

2. Switch to the Tuner operating

mode by pressing the button

TUNER/BAND (23)/(56).

Manual station selection

1. Press button TUNER/BAND (23)/(56) repeatedly until the desired frequency band appears.

2. Press the buttons TUNING – or TUNING + (12)/(46) or (7)/(44) to tune to the desired radio

stations and have them indicated in the display (3).

3. Briey tapping the TUNING – or TUNING + button step by step alters the reception frequency

upward or downward.

Station search operation

1. Holding down one of the two buttons TUNING – or TUNING + (12)/(46) or (7)/(44) for approx. 1 second

starts the search operation and determines the direction of the search. The search operation

simply nds stations with strong signals. Stations with weak reception can only be tuned

in manually.

2. Hold the TUNING – or TUNING + button to start the station search again. During the search

operation, the tuner is muted.

Amplier and Radio Operation - continued

CAUTION Listening at high volumes for an extended period of time may cause

damage to the users hearing.

OPERATIONAL INSTRUCTIONS

Amplier and Radio Operation - continued

Stereo / Mono

Repeatedly pressing the button

ST. / MONO (11) switches between

stereo and mono reception.

The stereo reception of a station

in the FM band is indicated

on the display (3)

In the case of stereo stations with a bad (noisy) reception, we recommend switching tuner to mono

reception. Press the ST. / MONO button. In the display (3), the message STEREO will disappear in

mono mode.

Tuner preset station

Each time the MEM./CLK ADJ. button (22)/(53) is pressed, the memory positions are called up one

after another in ascending number order.

The memory positions are selected directly using the numerical keys 1 - 0 / +10 (35) on the

remote control.

1. Program sites 1 – 9: Press the corresponding key 1- 9.

2. Program sites 10 – 19: Press button +10 and then the appropriate button 0 - 9.

3. Program site 20: Press button +10 twice and then the button 0.

Programming AM and FM stations in memory

The program memory allows you store 32 stations in FM and AM range. Program place selection is

described in the previous operating section.

1. In TUNER mode, select FM or

AM reception

2. Seek out the station required by

“Manual station selection” or

“Station search operation”

3. Press the MEM./CLK ADJ. (22)/(53)

and then press the REPEAT/PRESET

(8, front panel) or REPEAT/PRESET

(36, remote) until the desired memory preset appears.

iLuv | 16i9300 | V10M10_IM_EN_1111200815 | iLuv

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Iluv i9300 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info