669810
36
Zoom out
Zoom in
Vorherige Seite
1/51
Nächste Seite
Upgrade procedure
1) Remove props, connect a Lipo.
2) Attach the Vortex to a Windows PC or a Mac using a standard Micro-USB cable (ensure
that
this
is
a
full
USB
cable,
and
not
a
power-only
cable
shipped
with
some
products)
3) Start Vortex-configurator from chrome://apps/
4) Make sure the right COM port is selected and press the Flash Firmware button.
5) Point to the update file (OSD_vX.X.X.X.fw) downloadable from the Vortex 230 Mojo product page on
the ImmersionRC website, and start the update.
If during a previous upgrade you had a problem causing the OSD to be bricked, you can still recover from this
state using the procedure below:
Upgrade procedure for bricked OSD
1) Press and hold the button on top of the Synergy flight controller (accessible through a hole in the front
of the battery pad).
2) Remove props, plug in the Lipo ( while still holding the fusion board button ).
3) Release Synergy board button after 2 seconds.
4) Plug to USB
5) Start Vortex-configurator from chrome://apps/
6) Make sure the right COM port is selected and press the Flash Firmware button.
7) Point to the update file downloadable from the Vortex product page on the ImmersionRC website, and
start the update.
Flight Controller Firmware Upgrades
To upgrade the Flight-Controller firmware, the same Vortex Configurator tool may be used.
Simply select the BetaFlight .hex file instead of the OSD .fw file when flashing. Use the betaflight configurator
to configure the flightcontroller after successful flashing.
NOTE: If flashing fails wait a few seconds and retry by clicking Flash Firmware. Sometimes it may need
few attempts before it starts flashing,  so keep trying. If after 5 retries it's still not working, retry the
entire procedure.
Note that from time to time you may receive a ‘STM32 - timed out, verification steps failed’ message. As
long as this states ‘verify’, and not ‘program’, you may safely ignore it (this was resolved in recent
versions of firmware).
NOTE: Upgrading Betaflight to a version not supported by the OSD firmware can easily result in the OSD
not functioning. Please refer to the Vortex product page on the ImmersionRC website for compatibility
information.
NOTE: When Vortex will detect a new flight-controller version, it will automatically restart in TX Wizard
mode.  If not, force the TX Wizard using the Vortex app.
36
36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ImmersionRC Vortex 230 Mojo wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von ImmersionRC Vortex 230 Mojo

ImmersionRC Vortex 230 Mojo Kurzanleitung - Deutsch - 21 seiten

ImmersionRC Vortex 230 Mojo Kurzanleitung - Englisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info