Bedienungsanleitung Indesit BTW D71253 (Seite 9 von 13) (Englisch)

685466

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

EN 8

Lid seal

• Check the condition of the lid seal periodically and

clean it from time to time with a damp cloth.

Water inlet hose(s)

• Check the hose regularly for brittleness and cracks.

Replace if necessary.

Filter

• Check and clean the ﬁlter regularly, at least 3 or

4 times a year (see “Cleaning the Filter/ Draining

Residual Water”).

Do not use ﬂammable ﬂuids for cleaning the

appliance.

Recovering an object that falls between

the drumand the tub

If an object accidentally falls between the drum and

the tub, you can recover it thanks to one of the remov-

able drum blades:

1. Unplug the washing machine.

2. Remove the laundry from the drum.

3. Close the drum ﬂaps and turn the drum a

half-turn (picture 26).

4. Using a screw-driver, press on the plastic end while

sliding the blade from left to right (picture 27, 28).

5. It will fall into the drum.

6. Open the drum: you can recover the object

through the hole in the drum.

7. Reﬁt the blade from inside the drum: Position the

plastic tip above the hole on the right side of the

drum (picture 29).

8. Then slide the plastic blade from right to left until

it clips.

9. Close the drum ﬂaps again, turn the drum through

half a turn and check the positioning of the blade at

all its anchorage points.

10. Plug the washing machine in again.

REMAINING MOISTURE CONTENT OF THE LAUNDRY

AFTER SPINNING

The degree of moisture remaining in the laundry

after spinning mainly depends on the fabric type, the

selected programme and spin speed.

The lowest remaining moisture content can be

achieved using the wash programme referred to by

the Energy Label, with maximum spin speed. This

programme is marked in the separate programme

chart as “Reference programme for the Energy Label”.

Below a survey of the remaining moisture content

(in %) related to the various spin-drying efﬁciency

classes:

TRANSPORT AND HANDLING (picture 30)

1. Unplug the washing machine.

2. Turn off the tap.

3. Remove the water supply and drain hose.

4. Eliminate all water from the hoses and the washing

machine (see “Cleaning the Filter/ Draining

Residual Water”). Wait for the water to cool so as to

avoid any accidents.

5. To facilitate moving the machine, pull the handle

situated at the bottom front (if available on your

model) out a little by hand and pull it out to the stop

with the foot. Afterwards push the handle back into

the original stable position.

6. Fix the transport bracket again for transportation.

7. Transport the washing machine upright.

IMPORTANT: Do not use the washing machine while

the handle is pulled out.

Spin-drying efﬁciency

class

Remaining moisture

content in %

A (= most efﬁcient) less than 45

B 45 or more, but less than 54

C 54 or more, but less than 63

D 63 or more, but less than 72

E 72 or more, but less than 81

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit BTW D71253 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit BTW D71253

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info