Bedienungsanleitung Indesit D41 (Seite 11 von 16) (Englisch)

46840

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Cleaning and Special Maintenance

Troubleshooting

It may occur that the dishwasher does not function or does

not function properly. Before calling for assistance, let us

see what can be done first: have you forgot to press one of

the buttons or to perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient

pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you put the right amount of detergent into the

dispenser?

Is the wash cycle suitable for the dishes you have placed

inside the appliance?

Are the filter and microfilter clean?

Can the sprayer arms turn freely?

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

Error messages

Your dishwasher is equipped with a safety system which is

able to detect any operating anomalies. These anomalies

are reported by one or two cycle phase indicator lights "G"

flashing rapidly. Take a note of which lights are flashing,

turn the appliance off and call for technical assistance.

Tap off alarm

If you have forgotten to turn the water tap on, your appliance

will remind you of this by sounding a few short beeps for a

few minutes. Turn the tap on and your appliance will start

up again after a few minutes. Were you to be absent when

these beeps are sounded, the appliance will be blocked

automatically and cycle phase 2 and 3 indicator lights (wash

and rinses) will flash rapidly. Turn the appliance off at the

ON-OFF button,turn on the water tap and wait approximately

20 seconds before turning the appliance back on, now the

program will start.

If, despite all these checks, the dishwasher still does not

function and/or the problem persists, contact the nearest

authorised service centre and provide them with the

following information:

- the nature of the problem;

- the model type number (Mod. ...) and the serial number

(S/N ....), which are indicated on the plate located on the

side of the inner part of the door.

Never call on unauthorised technicians and refuse to

allow parts to be installed that are not original spare

parts.

The filter assembly

If you want consistent good results from your dishwasher,

you need to clean the filter assembly; this way the food

particles are

removed from

the wash water,

allowing it to be

recirculated

during the cycle,

filtered perfectly.

For this reason, it

is a good idea to

remove the larger

food particles

trapped inside

the cup “C” and semi-circular filter “A” after each wash.

All you need to do is rinse them under running water; to

remove these, pull the cup handle upwards. The entire

filter assembly, comprising a semi-circular filter “A”, a cup

“C”, and a cylindrical filter “B” should be cleaned thoroughly

once a month. Rotate filter “B” anticlockwise to remove it.

For cleaning, use a non metallic brush.

Reassemble the three parts as shown in the figures and

reinsert the whole assembly into the dishwasher, positioning

it into its housing and pressing downwards.

The dishwasher is not to be used without filters. Improper

replacement of the filters may reduce the efficiency of the

wash and even damage your dishwasher.

Cleaning the Sprayer Arms

It may happen that food particles

become encrusted on the

sprayer arms and block the

holes.Check the sprayer arms

periodically and clean them

when needed (see “Close-up

View [interior]”, letters F-I).

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure 2 under

"Installation") located on the outlet of the water supply

tap. After turning off the water tap, unscrew the end of

the water supply hose, remove the filter and clean it carefully

under running water. Then, return the filter to its place and

tighten the water supply hose back into position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit D41 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info