Bedienungsanleitung Indesit D63 (Seite 6 von 11) (Englisch)

46844

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Turning on the Appliance

Wash Cycle Adjustment Buttons

"Intensive 65°C" Button

This button (see "Close-up View - Control Panel", letter "E")

is used with the normal cycle in the case where pots and

pans with dry caked-on food must be washed.

This is not recommended for delicate items in so far as the

high temperatures could make their surfaces opaque or lighten

decorative colors after repeated washing.

Starting a wash cycle....

1. Make sure that the plug for the appliance is inserted into

the wall socket.

2. Make sure that the water supply is turned on to full

pressure.

3. Load the dishwasher (see the section entitled, "Loading

the Dishwasher").

4. Pour in the detergent (see the section entitled, "Salt,

Detergent and Rinse Aid").

5. Turn the knob located on the right of the control panel in

the clockwise direction until the number or symbol for the

cycle setting is aligned with the reference mark (see the

section entitled, "Wash Cycle Table").

6. Press the ON-OFF botton, and the ON-OFF light will turn

on. At this point, the wash cycle will begin.

Cancelling or modifying a wash cycle setting...

Premise: A cycle that is underway can only be modified if it has

only been running for a short time. Otherwise, the detergent may

have already been used, and the appliance may have already drained

the wash water. If this is the case, the detergent dispenser must be

refilled (see the paragraph entitled, "Loading the Detergent").

Press the ON-OFF button, and the ON light will turn off. Rota-

te the knob in the clockwise direction to the desired cycle

setting (see the section entitled, "Starting a wash cycle...").

Then, turn the dishwasher back on using the ON-OFF button.

If you forget to load some of the dishes...

The wash cycle can be interrupted by pressing the ON-OFF

button. You can then load additional dishes and turn the

appliance back on. The cycle will start where it left off.

At the end of the wash cycle...

When the knob stops turning and is aligned with a STOP

mark (see figure), the cycle has finished.

Turn off the appliance using the ON-OFF

button, turn off the water supply and

open the door of the dishwasher.

Wait a few minutes before unloading the

dishwasher to avoid handling the dishes

and utensils while they are still hot and

more susceptible to breakage. They will

also dry better.

STOP

"Half Load "Button"

This button (see "Close-up View - Control Panel", letter "F")

makes it possible to wash dishes using only the upper rack if

there are not enough dishes for a full load. This will allow

you to save on water and electrical energy.

It can be used before setting any of the wash cycles, except

for the intensive cycles (if included in the wash cycle table).

Please keep in mind that the amount of detergent should

also be cut in half.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit D63 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info