Bedienungsanleitung Indesit DE73 (Seite 9 von 16) (Englisch)

46850

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Turning on the Appliance

How to start a wash cycle…

After performing all the operations described in the previous

chapters, turn the water tap on completely, press ON-OFF

button "A" situated on the control panel, indicator light "B"

comes on.

The display turns on and the 3 dashes appear, indicating that

the dishwasher is awaiting instructions.

Starting and setting the cycle.

Turn the cycle selector "M" until the reference notch on the

knob corresponds with the symbol or number of the cycle

you wish to set (consult the wash cycle table contained in

this manual, especially when first using the appliance).

After a few seconds, a beep indicates the wash cycle has

started and indicator "G" displays the phase with which it

has begun. The counter "L" will indicate the amount of time

left until the end of the wash cycle.

Cancelling or modifying a wash cycle in progress…..

Premise: a wash cycle in progress can only be modified if it

hasn't been running for long.

To modify a wash cycle in progress, turn knob "M" until it

reaches the RESET position.

After a few seconds, you will hear 4 beeps, indicator "G"

relating to the phase under way will come off and 3 dashes

will appear. At this point, all the settings will have been

cancelled.

To select a new wash cycle, repeat the instructions contained

in the paragraph entitled "Starting and setting the cycle"

If you have left out a dish…

You can interrupt a wash cycle by pressing the ON-OFF button,

then place the forgotten dishes into the appliance, which

will start up from where it was interrupted when you turn it

back on.

Cycle phase underway indicator

Your dishwasher is equipped with an indicator "G" comprising

4 symbols which represent the different phases of a wash

cycle. When the wash cycle has started, the display will indi-

cate the phases underway in sequence.

These phases are:

pre-wash, wash, rinses, drying.

At the end of the wash cycle….

The end of the wash cycle is signalled by 2 beeps, and a

flashing "END" will come up on the display. Bring the selector

back to the RESET position, and the 3 dashes for

programming cancellation will appear.

Turn the appliance off by pressing the ON-OFF button, turn

off the water tap and open the door. Wait a few minutes

before removing the dishes: this way you won't have to

handle them while they're still hot and they will dry better.

How to eliminate the drying phase.

To eliminate the drying phase from the wash cycle you wish

to start, just turn the knob to the Reset position then first

and foremost set any preferences as to:

Þ upper or lower rack

Þ delayed start

Start the wash cycle by following the instructions. Symbol

relating to the drying phase will flash for approximately

4 seconds; immediately press button "I" and the symbol will

disappear, thus indicating that the drying phase has been

eliminated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit DE73 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info