Bedienungsanleitung Indesit DI6 (Seite 10 von 11) (Englisch)

46858

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Troubleshooting

It may occur that the dishwasher does not function or does

not function properly. Before calling for assistance, let us

see what can be done first: have you forgot to press one of

the buttons or to perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient

pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you put the right amount of detergent into the

dispenser?

Is the wash cycle suitable for the dishes you have placed

inside the appliance?

Are the filter and microfilter clean?

Can the sprayer arms turn freely?

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

Error messages.

Your dishwasher is equipped with a safety system which is able to

detect any operating anomalies. These anomalies are reported by

one or two wash cycle indicator lights "C" flashing rapidly.

Take a note of which lights are flashing, turn the appliance off and

call for technical assistance.

Tap off alarm

If you have forgotten to turn the water tap on, your appliance will

remind you of this by sounding a few short beeps for a few minutes.

Turn the tap on and your appliance will start up again after a few

minutes. Were you to be absent when these beeps are sounded, the

appliance will be blocked automatically and indicator lights 2 and 3

(Normal and Soak) will flash rapidly. Turn the appliance off at the

ON-OFF button, turn on the water tap and wait approximately 20

seconds before turning the appliance back on; repeat the

programming operations and the selected wash cycle will start up

again.

Clogged filter alarm

If the appliance is blocked and indicator lights 1 (Intensive) and 3

(Soak) flash rapidly, this means the filter is clogged by large particles

of food residue. Turn the appliance off, clean the filter thoroughly

and reposition it in its seat as illustrated on this page. Then turn it

back on. Repeat the programming operations and the selected wash

cycle will start up again.

If, despite all these checks, the dishwasher still does not

function and/or the problem persists, contact the nearest

authorised service centre and provide them with the

following information:

- the nature of the problem;

- the model type number (Mod. ...) and the serial number

(S/N ....), which are indicated on the plate located on the

side of the inner part of the door.

Never call on unauthorised technicians and refuse to

allow parts to be installed that are not original spare

parts.

The filter assembly

If you want consistent good results from your dishwasher, you need

to clean the filter assembly.

The food particles are removed

from the wash water, allowing

it to be recirculated during the

cycle, filtered perfectly. For this

reason, it is a good idea to

remove the larger food particles

trapped inside the semi-circular

filter A and cup “C”after each

wash; to remove the filter

assembly, pull the cup handle

upwards. All you need to do is

rinse them under running water.

The entire filter assembly should

be cleaned thoroughly once a

month: semi-circular filter A +

cup C + cylindrical filter B+ microfilter D.

To remove filter “B”, turn it anti-clockwise. Use a small non-metallic

brush for cleaning.

Reassemble the filter parts (as shown in the figure) and reinsert the

whole assembly into the dishwasher. Position it into its housing

and press downwards.

Cleaning and Special Maintenance

The dishwasher is not to be used without filters. Improper replace-

ment of the filters may reduce the efficiency of the wash and even

damage your dishwasher.

Cleaning the Sprayer Arms

It may happen that food particles become encrusted on the sprayer

arms and block the holes. Check the sprayer arms periodically and

clean them when needed (see “Close-up View [interior]”, letters F-

I).

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure 2 under

"Installation") located on the outlet of the water supply tap. After

turning off the water tap, unscrew the end of the water supply

hose, remove the filter and clean it carefully under running water.

Then, return the filter to its place and tighten the water supply hose

back into position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit DI6 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info