Bedienungsanleitung Indesit DI67 (Seite 8 von 16) (Englisch)

46864

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Turning on the Appliance

First of all....

After having completed all of the installation steps in the

preceding paragraphs, turn on the water to the unit and

press the ON-OFF button (A) located on the control panel.

The "B" indicator light will come on. At this point, the

appliance is on and ready to be programmed.

Starting and selecting the cycle...

Turn the cycle selector knob "D" until the reference notch

on the knob corresponds with the symbol for the cycle you

wish to set (have a look at the wash cycle table on page 7).

After a few seconds, you will hear a short beep and the

indicator light “G” comes on, indicating that the wash cycle

has begun and it is not advisable to make any changes at

this point.

Cycle phase indicator lights

The dishwasher is provided with 4 indicator lights "G" which

come on in sequence as the appliance is performing that

specific phase of the wash cycle.

These phases are, from left to right:

pre-wash, wash, rinses, drying

Cancelling or modifying a wash cycle in progress…..

Premise: You can cancel the wash cycle in progress, if it has

only just started.

To modify a wash cycle in progress, turn the knob anti-

clockwise and set it to Reset, after a few seconds you will

hear 3 beeps and indicator light "G" will go out: this means

all the settings have been cancelled. You are now free to re-

set the correct wash cycle.

If you forget to load some of the dishes...

The wash cycle can be interrupted by pressing the ON-OFF.

You can then load additional dishes and turn the appliance

back on. The cycle will start where it left off.

At the end of the wash cycle….

The end of the wash cycle is signalled by 2 short beeps and

a flashing drying phase indicator light “G”. Set the knob to

the Reset position to clear all settings.

Turn the appliance off by pressing button "A", thus cutting

off the electricity supply.

Turn off the water tap.

Wait a few minutes before unloading the dishes: they are

very hot! If you wait a little while, they dry better thanks to

the steam.

Empty the lower rack first.

Make sure the wash cycle has ended before removing the

dishes!

There's been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity

comes back on or when you close the door.

Warning: if opening the door soon after the end of the

programme,or during it, stand away from the Dishwasher,

to avoid possible injury from hot steam

Wash Cycle Adjustement Button

"1/2 LOAD" Button

This button (see "Close-up View - Control Panel", letter "N")

makes it possible to wash dishes using only the upper rack if

there are not enough dishes for a full load. This will allow

you to save on water and electrical energy.

It can be used before setting any of the wash cycles.

Please keep in mind that the amount of detergent should

also be cut in half.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit DI67 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info