Bedienungsanleitung Indesit DI67 (Seite 12 von 16) (Englisch)

46864

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Installation

Positioning the Appliance

Position the appliance in the desired location. The back

should rest against the wall behind it, and the sides, along

the adjacent cabinets or wall. The dishwasher is equipped

with water supply and drain hoses that can be positioned

to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher,

making it level. In any case, the appliance should not be

inclined more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

This dishwasher model can be built-in under the one

worktop, and it therefore comes provided with an assembly

kit complete with an instructions sheet.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas)

connector, inserting the small filter supplied with the

dishwasher and making sure

that it is fastened tightly in

place (see figure 2).

If the water pipes are new or

have not been used for an

extended period of time, let the

water run to make sure that the

water is clear and free of

impurities. If this precaution is

not taken, there is a risk that

the water inlet can get blocked

and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to

the house's hot water line (centralised system, heating

system), as long as it does not exceed a temperature of 60°

In this case, the wash cycle time will be shortened by about

15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the cold

water line.

Drain Hose Connection

Insert the drain hose into a

drain pipe with a minimum

diameter of 4 cm., or let it run

into the sink, making sure to

avoid bending or crimping it.

Use the speical plastic support

that comes with the appliance

(see figure to the right). The

free end of the hose must be

at a height between 40 and

100 cm.and must not be

immersed in water.

Attention: The special plastic hose support must be solidly

fastened to the wall to prevent the drain hose from moving

and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values

for the current in the home correspond to those on the

rating plate (located on the stainless steel inner door of the

appliance) and that the electrical system is sized for the

maximum voltage on the rating plate, insert the plug into

an electrical socket which is earthed properly (the earthing

of the appliance is a safety requirement mandated by law).

If the electrical socket to which the appliance must be

connected is not appropriate for the plug, replace the plug,

rather than using adpators or the like as they could cause

overheating and burns.

Should the electricity supply cable be damaged, we

recommend that you only contact authorised Technical

Service Centres for the replacement.

Fig.2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit DI67 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info