Bedienungsanleitung Indesit dv 640 a ix (Seite 22 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

124778

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Installation

Positioning the Appliance

Position the appliance in the desired location. The back

should rest against the wall behind it, and the sides, along

the adjacent cabinets or wall. The dishwasher is equipped

with water supply and drain hoses that can be positioned to

the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher, making

it level. In any case, the appliance should not be inclined

more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

Cold Water Connection

This electric household appliance should be connected to

the water mains using the cold water supply hose provided

with the appliance only. Do not use a different hose. In the

event of replacements, use original spare parts only.

Connect the cold water supply hose to a 3/4 gas threaded

connection, taking care to screw it tightly onto the tap. If the

water hoses are new or have been out of use for an extended

period of time, let the water run to make sure it is clear and

free of impurities before making the connection. If this

precaution is not taken, the water inlet could get blocked,

causing damage to your dishwasher.

Hot Water Connection

The water supply to the appliance can also be connected to

the house's hot water line (centralised system, heating

system), as long as it does not exceed a temperature of 60°

In this case, the wash cycle time will be shortened by about

15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the cold

water line.

Anti-flooding protection

Your dishwasher is provided with a special system which

blocks the water supply in the event of leaks inside the

appliance. It is further equipped with a water inlet hose that

can withstand extremely high pressures and that turns bright

red in the event of breakage. Safety in the event of flooding

is ensured by the second clear hose that contains the former

and thus highlights the latter when it has turned bright red. It

is vital that you check it on a regular basis: if you see it has

turned bright red, then you know you have to replace it as

soon as possible. Call for an authorised technical engineer to

come and replace it.

Drain Hose Connection

Fit the drain pipe into a drain line with a minimum diameter

of 4 cm or place it over the

sink. Avoid restricting or

bending it. Use the special

plastic elbow provided (see fi-

gure) to position it in the best

possible way. The part of the

pipe marked with the letter A

should be between 40 and 100

cm above the ground.

The pipe should not be

immersed in water.

Attention: The special plastic hose support must be solidly

fastened to the wall to prevent the drain hose from moving

and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for

the current in the home correspond to those on the rating

plate (located on the stainless steel inner door of the

appliance) and that the electrical system is sized for the

maximum voltage on the rating plate, insert the plug into

an electrical socket which is earthed properly (the earthing

of the appliance is a safety requirement mandated by law).

If the electrical socket to which the appliance must be

connected is not appropriate for the plug, replace the plug,

rather than using adpators or the like as they could cause

overheating and burns.

Caution: the dishwasher plug must be accessible even when

the appliance is installed as a built-in unit so that maintenance

can be done safely.

Should the electricity supply cable be damaged, we

recommend that you only contact authorised Technical Service

Centres for the replacement.

Condensation-proof tape.

On some models, a transparent condensation-proof adhesive

tape has been provided.

It should be stuck onto the lower side of your wooden worktop

to protect it from the formation of condensation.

When not provided, this tape can be requested as a spare

part from authorised retailers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit dv 640 a ix Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info