Bedienungsanleitung Indesit FI26 KB IX (Seite 14 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

451558

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

DATA PLATE

Dimensions

width cm 43.5

height cm 32

depth cm 43,5

Volume

lt. 60

Dimensions

(models with self-

cleaning panels)

width cm 43.5

height cm 32

depth cm 40

Volume (models

with self-cleaning

panels)

lt. 56

Electrical

connections

voltage: 220-230V ~ 50/60 Hz or

50Hz (see data plate)

maximum power absorbed 2250W

Directive 2002/40/EC on the label

of electric ovens.

Standard EN 50304

ENERGY LABEL

Energy consumption Class

certification Natural convection

heating mode: Convection

mode.

This appliance conforms to the

following European Economic

Community directives:

- 2006/95/EEC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 2004/108/EEC of 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments;

- 93/68/EEC of 22/07/93 and

subsequent amendments.

- 2002/96/EC and subsequent

amendments.

Electrical connections

! Ovens equipped with a three-pole power supply

cable are designed to operate with alternating current

at the voltage and frequency indicated on the data

plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(see diagram).

2. Loosen the cable

clamp screw and

remove it, using a

screwdriver as a lever

(see figure).

3. Remove the wire

contact screws L-N-

, then fasten the wires

under the screw heads,

respecting the colour

code: Blue (N), Brown

(L) and Yellow-Green

Verde (

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (see side).

The appliance must be directly connected to the

mains using an omnipolar circuit-breaker with a

minimum contact opening of 3 mm installed between

the appliance and the mains, suitable for the load

indicated and complying with current electrical

regulations (the earthing wire must not be interrupted

by the circuit-breaker). The supply cable must not

come into contact with surfaces with temperatures

higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant

with safety regulations.

Before connecting to the power supply, make sure

that:

 The appliance is earthed and the plug is compliant

with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated on the data plate

(see below).

 The voltage must be in the range between the

values indicated on the data plate (see below).

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only (see Assistance).

The manufacturer declines any liability should

these safety measures not be observed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit FI26 KB IX Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info