Bedienungsanleitung Indesit FM 10 RK.C RA (Seite 20 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

513209

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Instalation

The appliance must be installed only by a qualified

person in compliance with the instructions provided.

The manufacturer declines all responsibility for improper

installation which may harm persons and animals and

damage property.

Important: The power supply to the appliance must be

cut off before any adjustments or maintenance work is

done on it.

Installation of Built-in Ovens

In order to ensure that the built-in appliance functions prop-

erly, the cabinet containing it must be appropriate. The

figure below gives the dimensions of the cut-out for instal-

lation under the counter or in a wall cabinet unit.

In order to ensure adequate ventilation, the back panel of

the cabinet unit must be removed. Installing the oven so

that it rests on two strips of wood is preferable. If the oven

rests on a continuous, flat surface, there must be an ap-

erture of at least 45 x 560 mm.

The panels of the adjacent cabinets must be made of heat-

resistant material. In particular, cabinets with a veneer ex-

terior must be assembled with glues which can withstand

temperatures of up to 100 °C.

In compliance with current safety standards, contact with

the electrical parts of the oven must not be possible once

it has been installed.

All parts which ensure the safe operation of the appliance

must be removable only with the aid of a tool.

To fasten the oven to the cabinet, open the door of the

oven and attach it by inserting the 4 wooden screws into

the 4 holes located on the perimeter of the frame.

Electrical Connection

Those ovens equipped with a three-pole power supply

cable are designed to operate with an alternating current

with the voltage and frequency indicated on the data plate

(located on the appliance) and in the instruction manual.

The wire for earthing the appliance is yellow-green in col-

our.

Fitting on a Power Supply Cable

Opening the terminal board:

• Using a screwdriver, prise on the side tabs of the ter-

minal board cover;

• Pull open the cover of the terminal board.

To install the cable, proceed as follows:

• Remove the wire clamp screw and the three contact

screws L-N-6

• Fasten the wires beneath the screwheads using the

following colour scheme: Blue (N) Brown (L) Yellow-

Green 6

• Fasten the supply cable in place with the clamp and

close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indi-

cated on the data plate. When connecting the cable di-

rectly to the mains, install an omnipolar circuit-breaker with

a minimum contact opening of 3 mm between the appli-

ance and the mains. The omnipolar circuit breaker should

be sized according to the load and should comply with

current regulations (the earth wire should not be inter-

595 mm.

24 mm.

545 mm.

5 mm.

567 mm.

23 mm.

593 mm.

45 mm.

558 mm.

N.B.: Installation in compliance with the consumption declaration

595 mm.

24 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

558 mm.

595 mm.

45 mm.

min.

45 mm.

min.

560 mm.

45 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit FM 10 RK.C RA Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info