Bedienungsanleitung Indesit I5GS1G (Seite 18 von 40) (Englisch, Holländisch, Französisch)

577352

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

! If one or more of these conditions is not fulfilled or if

the cooker must be installed according to the conditions

listed for class 2 - subclass 1 appliances (installed

between two cupboards), the flexible steel hose must

be used instead (see below).

Connecting a flexible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with current

national legislation.

To begin using the hose, remove the hose holder on the

appliance (the gas supply inlet on the appliance is a

cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres, making

sure that the hose is not compressed and does not come

into contact with moving parts.

Checking the connection for leaks

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never use

a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other

than the default type (this is indicated on the rating label

on the cover).

Adapting the hob

Replacing the nozzles for the hob

burners:

1. Remove the hob grids and

slide the burners off their seats.

2. Unscrew the nozzles using a 7

mm socket spanner (see figure),

and replace them with nozzles

suited to the new type of gas(see Burner and nozzle

specifications table).

3. Replace all the components by following the above

instructions in reverse.

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until the

flame is small but steady.

! If the appliance is connected to a liquid gas supply, the

regulatory screw must be fastened as tightly as possible.

3. While the burner is alight, quickly change the position of the

knob from minimum to maximum and vice versa several times,

checking that the flame is not extinguished.

! The hob burners do not require primary air adjustment.

Adjusting the gas oven burner’s minimum setting:

1. Light the burner (see Start-up and Use).

2. Turn the knob to the minimum position (MIN) after it has

been in the maximum position (MAX) for approximately

10 minutes.

3. Remove the knob.

4. Tighten or loosen the adjustment screws on the outside

of the thermostat pin (see figure) until the flame is small

but steady.

! If the appliance is connected to liquid gas, the

adjustment screw must be fastened as tightly as possible.

5. Turn the knob from the MAX position to the MIN position

quickly or open and shut the oven door, making sure that

the burner is not extinguished.

WARNING! The glass lid can

break in if it is heated up. Turn off

all the burners and the electric

plates before closing the lid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit I5GS1G Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info