Bedienungsanleitung Indesit I5V7H6A (Seite 19 von 76) (Deutsch, Englisch, Französisch, Polnisch)

577360

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

! Before operating your new appliance please read

this instruction booklet carefully. It contains important

information concerning the safe installation and

operation of the appliance.

! Please keep these operating instructions for future

reference. Make sure that the instructions are kept with

the appliance if it is sold, given away or moved.

! The appliance must be installed by a qualified

professional according to the instructions provided.

! Any necessary adjustment or maintenance must be

performed after the appliance has been disconnected

from the electricity supply.

Positioning and levelling

! It is possible to install the appliance alongside

cupboards whose height does not exceed that of the

hob surface.

! Make sure that the wall in contact with the back of

the appliance is made from a non-flammable, heat-

resistant material (T 90°C).

To install the appliance correctly:

• Place it in the kitchen, the dining room or the bed-sit

(not in the bathroom).

• If the top of the hob is higher than the cupboards,

the appliance must be installed at least 200 mm away

from them.

• If the cooker is installed

underneath a wall cabinet,

there must be a minimum

distance of 420 mm

between this cabinet and

the top of the hob.

This distance should be

increased to 700 mm

if the wall cabinets are

flammable (see figure).

• Do not position blinds behind the cooker or less than

200 mm away from its sides.

• Any hoods must be installed according to the

instructions listed in the relevant operating manual.

Levelling

If it is necessary to level the

appliance, screw the adjustable

feet* into the places provided

on each corner of the base of

the cooker (see figure).

The legs* provided with the

appliance fit into the slots on

the underside of the base of the

cooker.

Electrical connections

Fitting the power supply cable

The cable should be suited to the type of electrical

connection used, according to the following connection

diagram:

To install the power supply cable correctly:

1. Loosen the screw V in

the terminal board and

pull the cover to open it

(see figure).

2. Position the connection

support A (see figure)

according to the

connection diagram

shown above. The

terminal board is

designed for single-

phase 230 V connection:

terminals 1, 2 and 3

are connected to each

other; jumper 4-5 is

located in the lower area of the terminal board.

3. Position wires N and



according to the diagram

(see figure) and perform the connection by tightening

the terminal board screws as much as possible.

4. Position the remaining wires on terminals 1-2-3 and

tighten the screws.

Installation

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

1 2

12345

400 3N

H05RR-F 5x2.5 CEI-UNEL 35363

H05VV-F 5x2.5 CEI-UNEL 35746

400V 2N

H05RR-F 4x4 CEI-UNEL 35363

H05VV-F 4x4 CEI-UNEL 35746

230V

H05RR-F 3x4 CEI-UNEL 35363

H05VV-F 3X4 CEI-UNEL 35746

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit I5V7H6A Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info