Bedienungsanleitung Indesit IDE1000 (Seite 7 von 13) (Englisch)

46872

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Turning on the Appliance

First of all

Insert the plug into the electricity socket to power the

dishwasher. Turn on the water tap completely and press ON-

OFF button "A"; the display lights up and the wash cycle

time selected on the knob will flash.

Selecting and starting a wash cycle.

• Select the desired wash cycle by turning knob "D"

clockwise from wash cycle 1 to 7 and anticlockwise from 7

to 1; the display indicates the average duration of the wash

cycle and the cycle phases it consists of (consult the wash

cycle table contained on page 7, especially when first using

the appliance).

• Press the Start button "R" and the wash cycle starts up,

emitting a double beep; the approximate amount of time

left until the end of the wash cycle is displayed.

• If the time indicated at the start of the wash cycle does

not correspond to the actual duration of the cycle itself, this

could be for a number of reasons: the temperature of the

inlet water, the degree of soil, prolonged attempts by the

appliance to clean the wash filter from food residue clogging

it, etc.

Cycle phase under way indicator

While the wash cycle is under way, the symbols corresponding

to the cycle phases light up in sequence.

Here are the symbols corresponding to each cycle phase:

Pre-wash Wash Rinses Drying

Cancelling and modifying a wash cycle in progress

Premise: a wash cycle in progress can only be modified if it

hasn't been running for long.

Keep the Reset button "R" pressed for about 3 seconds:

a prolonged beep will sound, followed by three short beeps.

The cancelled cycle time will flash on the display. Turn the

knob to select a new wash cycle.

You've left out a dish?

You can interrupt a wash cycle by pressing the "ON-OFF"

button, then place the forgotten dishes into the appliance,

which will start up, after approximately 10 seconds, from

where it was interrupted when you turn it back on.

There's been a power failure? Has the dishwasher door

been opened?

The wash cycle stops and 3 dashes appear on the display;

the cycle restarts as soon as the electricity comes back on or

when the door is shut.

At the end of the wash cycle

The end of the wash cycle is indicated by two short beeps

and the word "END" flashes on the display.

• Turn the appliance off at the ON-OFF button

• Turn off the water tap.

• Empty the lower rack first.

Make sure the wash cycle has ended before removing the

dishes!

Warning: when you open the dishwasher door after the wash

cycle has just ended or is under way, take care not to scald

yourself with the hot steam.

How to set the extra drying

Press button "E". After a prolonged beep, indicator light

"G" lights up and the time corresponding to the wash cycle

selected on the knob will flash on the display.

Note: The time indicated on the display is extended due to

the extra drying time.

To disable the extra drying option, press the same button

and indicator light "G" will be turned off after a beep is

sounded.

This option is incompatible with the soak cycle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IDE1000 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit IDE1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info