Bedienungsanleitung Indesit IDE1000 (Seite 14 von 16) (Englisch)

46872

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Electrical Connection

If your appliance is supplied with a 13 amp. fused plug it

can be plugged into a 13 amp socket for immediate use.

Before using the appliance please read the instruction below.

WARNING: THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse cover

re-fitted. If the fuse cover is lost, the plug must not be used

until a replacement is obtained.

Replacemente fuse covers:

If a replacement fuse cover is fitted, it must be of the correct

colours as indicated by the coloured marking or the colour

that is embossed in words on the base of the plug.

Replacements can be obtained directly from your nearest

Service Depot.

Removing the plug:

Ifyour appliance has a non-rewireable moulded plug and

you should wish to remove it to re-route the mains cable

through partitions, units etc., please esure that either:

- the plug is replaced by a fused 13 amp re-wireable plug

bearing the BSI mark of approval

- or:

- the mains cable is wired directly into a 13 amp cable outlet,

controlled by a switch, (in compliance with BS 5733) which

is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally inserted

into a socket.

Instruction for connecting cable to an altenative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

CAUTION:

The dishwasher plug must be accessible even when the

appliance is installed as a built-in unit so that maintenance

can be done safely.

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminal in your plug, proceed as follows:

connect Green & Yellow wire to terminal market “E” or

coloured Green or Green & Yellow.

Connect Brown wire to terminal marked “L” or coloured

Red.

Connect Blue wire to terminal marked “N” or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted with a

13 amp fuse. A15 amp plug must be protected by a 15

amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt about the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance

with the following code:

BLUE “NEUTRAL” (“N”)

BROWN “LIVE” (“L”)

GREEN AND YELLOW “EARTH” (“E”)

Disposing of the appliance:

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the plug

body and dispose of it as described above

GREEN &

YELLOW

BROWN

BLUE

13 amp fuse

CROSS-BAR

CORD GRIP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IDE1000 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit IDE1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info