Bedienungsanleitung Indesit IDL 51 (Seite 24 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch)

75239

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Installation

Positioning the Appliance

Position the appliance in the desired location. The back should

rest against the wall behind it, and the sides, along the

adjacent cabinets or wall. The dishwasher is equipped with

water supply and drain hoses that can be positioned to the

right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher, making

it level. In any case, the appliance should not be inclined

more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

This dishwasher model can be built under a single worktop

(please read the relevant instruction sheet).

Cold Water Connection

This electric household appliance should be connected to the

water mains using the cold water supply hose provided with

the appliance only. Do not use a different hose. In the event

of replacements, use original spare parts only.

Connect the cold water supply hose to a threaded 3/4 (gas)

threaded connection, taking care to screw it tightly onto the

tap.

If the water pipes are new or have not been used for an

extended period of time, let the water run to make sure that

the water is clear and free of impurities. If this precaution is

not taken, there is a risk that the water inlet can get blocked

and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to

the house's hot water line (centralised system, heating system),

as long as it does not exceed a temperature of 60° C.

In this case, the wash cycle time will be shortened by about

15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the cold

water line.

Anti-flooding protection

Your dishwasher is provided with a special system which blocks

the water supply in the event of leaks inside the appliance. It

is further equipped with a water inlet hose comprising an

outer clear hose and an inner red hose, which can both with-

stand extremely high pressures. Should the inner hose break,

the outer hose will consequently turn red. Safety in the event

of flooding is ensured by the second clear hose that contains

the former. It is vital that you check the outer hose regularly:

if you see it has turned bright red, then you know you have to

replace it

as soon as possible. Call for an authorised technical engi-

neer to come and replace it.

Drain Hose Connection

Fit the drain pipe into a drain

line with a minimum

diameter of 4 cm or place it

over the sink. Avoid

restricting or bending it. Use

the special plastic elbow

provided (see figure) to

position it in the best possible

way. The part of the pipe

marked with the letter A

should be between 40 and

100 cm above the ground.

The pipe should not be immersed in water.

Attention: The special plastic hose support must be solidly

fastened to the wall to prevent the drain hose from moving

and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for

the current in the home correspond to those on the rating

plate (located on the stainless steel inner door of the

appliance) and that the electrical system is sized for the

maximum voltage on the rating plate, insert the plug into an

electrical socket which is earthed properly (the earthing of

the appliance is a safety requirement mandated by law). If

the electrical socket to which the appliance must be connected

is not appropriate for the plug, replace the plug, rather than

using adpators or the like as they could cause overheating

and burns.

Should the electricity supply cable be damaged, we

recommend that you only contact authorised Technical Service

Centres for the replacement.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IDL 51 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info