Bedienungsanleitung Indesit idl 600 (Seite 8 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

123998

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

 Only use products that have been specifically

designed for dishwashers.

Do not use table salt or industrial salt.

 If using a multi-functional product (2-in-1, 3-in-1, 4-in-1) it

is not necessary to add rinse aid; however, we

recommend that you add salt, especially if you live in

an area where the water is hard or very hard. If you do

not add salt or rinse aid, the LOW SALT* and LOW

RINSE AID* indicator lights will flash continuously.

Loading the rinse aid

Rinse aid makes it easier for the crockery to dry, as

water runs off surfaces more readily and therefore

does not leave streaks or marks.

The rinse aid dispenser should be filled:

• whenever the indicator light (H) signals that it is

empty. Illuminated light: add rinse aid; unlit light:

there is no shortage of rinse aid in the dispenser.

• when the LOW RINSE AID* indicator light on the

panel flashes;

1. Open the dispenser by

turning the lid (G) in an

anticlockwise direction.

2. Pour in the rinse aid,

making sure it does not

overflow from the

dispenser. If this happens,

clean the spill immediately

with a sponge.

3. Screw the lid back on.

Adjusting the amount of rinse aid

If you are not completely satisfied with the washing or

drying results, you may adjust the quantity of rinse aid

used. Use a screwdriver to turn the dosage adjuster to

one of the 6 pre-set positions (the default position is

set to 4):

• if there are white streaks on the crockery, set the

adjuster to a lower number (1-3).

• if drops of water remain on the crockery or there

are limescale marks present after the cycle has

finished, set the adjuster to a higher number (4-6).

 If you are using multi-functional tablets (2-in-1, 3-in-1,

4-in-1) and you wish to further improve the drying

performance of the appliance, fill the dispenser and

set the dosage adjuster to 2.

Loading the refined salt

In order to obtain the best possible results from a

wash cycle, make sure that the dispenser is never

empty. Refined salt removes limescale from the water,

thus avoiding the formation of deposits on crockery.

The salt dispenser is located in the lower part of the

dishwasher (

see Description

) and should be filled:

• when the green float* cannot be seen by simply

looking at the cap of the salt dispenser;

• when the LOW SALT* indicator light on the panel

flashes;

• if your machine is not equipped with an indicator

light or a green float:

approximately every 30 wash cycles;

1. Remove the lower rack and unscrew the cap of the

dispenser (in an anti-clockwise

direction).

2. For the first wash cycle only:

fill the dispenser up to the

edges with water.

3. Position the funnel provided

correctly (

see figure

) and fill

the salt dispenser up to the

edges (approximately 2 kg); it is normal for a little

water to leak out.

4. Remove the funnel, wipe away any salt residue from

the thread and screw the cap on tightly, so that

detergent does not leak into the dispenser during the

wash cycle (this could damage the water softening

system beyond repair).

 When salt has been added, run a wash cycle

immediately, without crockery, in order to remove any

salt solution that has leaked out and to avoid

corrosion.

Adjusting the amount of salt*

It is possible to adjust the amount of salt used

according to the hardness of the water in your area

(this information is available from your local water

board).

1. Unscrew the dispenser cap.

2. Turn the arrow on the neck of the

dispenser (

see figure

) towards the +

or - symbols, using the table below

as a guide.

The default setting of the water softening system is +.

- If using multi-functional tablets (2-in-1, 3-in-1, 4-in-1) fill

the salt dispenser and set the adjuster to -; if the

hardness of the water is greater than 60°fH, set it to +.

* Only available in selected models.

Rinse aid and refined salt

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit idl 600 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info