Bedienungsanleitung Indesit idl 75 eu 2 (Seite 19 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

127055

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

How to start the dishwasher

How to start a wash cycle…

After performing all the operations described in the previous chapters,

turn the water tap on completely, press ON-OFF button “A” situated

on the control panel and indicator light “B” comes on.

At this point, the dishwasher is on and ready to be programmed.

Starting and selecting the cycle.

Turn the cycle selector knob “D” clockwise until the reference notch

on the knob corresponds with the number or symbol for the cycle

you wish to set (consult the wash cycle table on page 17, especially

when first using the appliance).

If the appliance door is shut, press the Start button “R” and you will

hear a beep; the cycle will start up within a few seconds.

Cycle phase indicator lights

The dishwasher is provided with 4 indicator lights “G” which come

on in sequence as the appliance is performing that specific phase of

the wash cycle.

These phases are:

pre-wash, wash, rinses, drying

Cancelling or modifying a wash cycle in progress…..

Premise: You can cancel the wash cycle in progress, if it has only just

started.

To modify a wash cycle, keep the RESET button “R” pressed for

about 5 seconds: a prolonged beep will sound, followed by three

short beeps. Indicator light “G” will turn off and at this point, all the

settings will have been cancelled.

To select a new wash cycle, repeat the operations illustrated in the

paragraph entitled “starting and selecting the cycle”.

Warning: the knob must be turned clockwise from wash cycle 1 to

7, an anti-clockwise from wash cycle 7 to 1.

If you have left out a dish…

You can interrupt a wash cycle by pressing the ON- OFF button,

then place the dishes you had left out into the appliance, which will

start up from where it was interrupted when you turn it back on.

There’s been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity comes

back on or when the door is shut.

At the end of the wash cycle….

The end of the wash cycle is indicated by two short beeps and the

flashing of the drying phase indicator light.

• Turn off the water tap.

• Wait a few minutes before unloading the dishes: if you wait a little

while they dry better thanks to the steam.

• Empty the lower rack first.

Warning:when you open the dishwasher door after the wash cycle

has just ended or is under way, take care not to scald yourself with

the hot steam.

How to set the delayed start

When you have loaded the dishes, you can choose when to start

your dishwasher before setting the wash cycle desired. Press button

“H” to delay the start of the wash cycle by 12, 9, 6 or 3 hours. Each

time you press it, you will hear a short beep and the indicator light

“G” corresponding to the selected delay will light up.

Now you can select the desired wash cycle. Press the start button

“R” and after you hear the beep, the countdown to the delayed

start will begin.

Once this time is up, the indicator light will stop flashing and the

wash cycle will begin.

If you have set a 12 hour delay, for example, once you have selected

the wash cycle, the 12 hour indicator light will flash, followed by

the others in sequence until the set time delay is up. A quick look at

the indicator lights will keep you informed of the countdown progress

at all times.

Have you changed your mind?

If you change your mind, you can set a shorter time delay: press

button “H” to select it. You need not reset the wash cycle.

If on the other hand you want to cancel the delay set and you want

the cycle to start immediately, press button “H” repeatedly until the

cycle starts and indicator light “G” corresponding to the cycle start

phase comes on.

Dual function of indicator lights “G”

1) flashing to indicate a delayed start:to remind you that you

have set a delayed start;

2) on and not flashing beneath the cycle phase symbol:

meaning the cycle has started and is in the phase indicated by the

symbol.

You want to wash on one rack only?

Remember to use half the amount of detergent.

When you only have little cutlery to wash, you can run just half a

load on the upper rack, saving on water, detergent and electricity.

• When you press the “I” button, you will hear a blip and the “L”

indicator light will light up.

Once you have made your selection, start the wash cycle by pressing

Start and it will wash the top rack only.

- This option is available with all wash cycles.

- The Just You wash cycle is programmed to wash on the

upper rack only.

Warning:

Turn the appliance off by pressing button “A”, unplug the

appliance from the electricity socket to cut off the power

supply; the power supply cable should consequently be

easily accessible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit idl 75 eu 2 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info