Bedienungsanleitung Indesit IDTM (Seite 16 von 24) (Englisch, Französisch)

24011

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

You have loaded your dishes and you now have

to set the wash cycle. It takes just one minute

to learn how

Starting the dishwasher

Ready, steady, go!

First of all.

Turn on the water tap completely

and press ON-OFF button "A". you

will hear a short beep and indicator

light "B" lights up. Now the

appliance is on and awaiting in-

structions.

Selecting the wash

cycle.

Select the wash cycle by pressing

button "P". Each time you press

the button, a beep will sound and

indicator lights "E" will light up in

sequence: choose the cycle you

deem most suited to the type of

dishes to be washed (take a look at

page 16, where you will find the

wash cycle table). If the appliance

door is shut, press the Start button

"R" and you will hear a beep; the

cycle will start up within a few

seconds.

The dishwasher informs

you.

Your dishwasher is fitted with

indicator lights (G) which light up

to indicate the cycle phase under

way.

Here are the symbols correspond-

ing to each cycle phase:

pre-wash, wash, rinses, drying.

At all times, your dishwasher tells

you which cycle phase is under

way.

Modifying a wash cycle

in progress.

But if you have chosen the wrong

cycle, not to worry! You can modify

the wash cycle in progress, if it has

only just started. Keep the RESET

button "R" pressed for about 5

seconds: a prolonged beep will

sound, followed by three short

beeps. Indicator light "G" will turn

off and at this stage, all the settings

will have been cancelled. You are

now free to re-set the correct wash

cycle.

You've left out a dish?

Well, it happens to everyone. Inter-

rupt the wash cycle by pressing the

ON-OFF button, insert the dish you

had forgotten and press the ON-

OFF button again. The cycle will

start up from where you interrupted

it.

Finished?

The end of the wash cycle is indi-

cated by two short beeps and the

flashing of the drying phase indica-

tor light.

 Turn the appliance off by press-

ing button "A", thus cutting off

the electricity supply.

 Turn off the water tap.

 Wait a few minutes before unload-

ing the dishes: they are very

hot! If you wait a little while, they

dry better thanks to the steam.

 Empty the lower rack first.

There's been a power

failure? Have you opened

the dishwasher door?

The wash cycle stops and then

restarts when the electricity comes

back on or when you shut the door.

Everything is under control!

You decide when it

starts.

When you have loaded the dishes,

you can choose when to start your

dishwasher before setting the wash

cycle desired. Press button "D" to

delay the start of the wash cycle

by 12, 9, 6 or 3 hours. Each time

you press it, you will hear a short

beep and the indicator light "G"

corresponding to the selected

delay will light up.

Now you can select the desired

wash cycle. Press the start button

"R" and after you hear the beep,

the countdown to the delayed start

will begin.

Once this time is up, the indicator

light will stop flashing and the wash

cycle will begin.

If you have set a 12 hour delay, for

example, once you have selected

the wash cycle, the 12 hour

indicator light will flash followed

by the others in sequence until the

set time delay is up. A quick look

at the indicator lights will keep you

informed of the countdown

progress at all times.

Have you changed your

mind?

If you change your mind, you can

set a shorter time delay: press but-

ton "D" to select it. You need not

reset the wash cycle.

If on the other hand you want to

cancel the delay set and you want

the cycle to start immediately,

press button "D" repeatedly until

the cycle starts and indicator light

"G" corresponding to the cycle

start phase comes on.

Dual function of indicator

lights "G"

1) flashing to indicate a

delayed start: to remind you

that you have set a delayed start;

2) on and not flashing

beneath the cycle phase

symbol:

meaning the cycle has started and

is in the phase indicated by the

symbol.

You want to wash on one

rack only? Remember to

use half the amount of

detergent.

If you only have a few dishes to

wash, you can decide to run a half-

load, to save on water, electricity

and detergent. Before setting any

wash cycle whatsoever, press but-

ton "F", indicator light "H" will light

up and your dishwasher will wash

on the upper rack only.

Would you like to see

which settings you have

made?

At any time, when the cycle is under

way, if you press button "P", the

cycle in progress indicator light will

light up for a few seconds, followed

by the half load indicator light,

wherever set.

If opening the

door soon after

the end of the

programme,or

during it, stand

away from the

Dishwasher, to

avoid possible

injury from hot

steam.

Make sure the

wash cycle has

ended before

removing the

dishes!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IDTM Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit IDTM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info