Bedienungsanleitung Indesit IDTM (Seite 15 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

24011

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a

drain duct with a minimum diameter of 4 cm.

Alternatively, rest it over a sink or tub; the free end

of the hose should not remain immersed in water.

The special plastic

elbow* makes it easier

to find the best layout:

fix the elbow to the wall

securely in order to

prevent the outlet hose

from moving and

spilling the dirty water.

The part of the hose

marked with the letter A

should be between 40

and 100 cm above the ground (see figure).

 We advise against the use of hose extensions.

Electrical connection

Before inserting the plug into the electrical socket,

make sure that:

 the socket is earthed and complies with current

regulations;

 the socket can withstand the maximum load of

the appliance, which is indicated on the data

plate located on the inside of the door (see

Description of the appliance);

 the power supply voltage falls within the values

indicated on the data plate on the inside of the

door;

 the socket is compatible with the plug of the

appliance. If this is not the case, ask an

authorised technician to replace the plug (see

Assistance); do not use extension cables or

multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket should be

easily accessible.

 The cable should not be bent or compressed.

 The cable should be checked regularly and

replaced by authorised technicians only (see

Assistance).

 The Company shall not be held responsible for any

incidents that occur if these regulations are not

observed.

Advice regarding the first wash cycle

After the appliance has been installed, immediately

before running the first wash cycle, completely fill

the salt dispenser with water and add approximately

2 kg of salt (see Rinse aid and refined salt). The

water may overflow: this is normal and is not a

cause for concern. It is also normal that the LOW

SALT* indicator light continues to flash for a few

cycles after the salt has been loaded.

* Only available in selected models.

Technical data

Dimensions

width 60 cm

height 85 cm

depth 60 cm

Capacity

12 standard place-settings

Water supply

pressure

30 KPa ÷ 1 MPa

(0,3 ÷ 10 bar)

4,3 psi-145 psi

Power supply

voltage

See appliance data plate

Total

absorbed

power

See appliance data plate

Fuse

See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-73/23/EEC dated 19/02/73

(Low Voltage) and subsequent

modifications

-89/336/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent modifications)

-97/17/EC (Labelling)

- 2002/96/EC(WEEE)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IDTM Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit IDTM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info