Bedienungsanleitung Indesit IDTM (Seite 4 von 12) (Englisch)

24011

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Electrical Connection

If your appliance is supplied with a 13 amp. fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instruction below.



WarningWarning

Warning:this appliance must be earthed.

Thed following operations should be carried out by a

qualified electrician.

Replacing the fuse

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacemente fuse covers

If a replacement fuse cover is fitted, it must be of

the correct colours as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug

Ifyour appliance has a non-rewireable moulded plug

and you should wish to remove it to re-route the

mains cable through partitions, units etc., please

esure that either:

- the plug is replaced by a fused 13 amp re-wireable

plug bearing the BSI mark of approval

or:

- the mains cable is wired directly into a 13 amp

cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instruction for connecting cable to an altenative

plug

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yellow -

EarthEarth

Earth

Blue -

NeutralNeutral

Neutral

Brown -

LiveLive

Live



Caution: Caution:

Caution: The dishwasher plug must be accessible

even when the appliance is installed as a built-in unit

so that maintenance can be done safely.

As the colours of the wires in the mains lead may

not correspond with the coloured markings

identifying the terminal in your plug, proceed as

follows:

• connect Green & Yellow wire to terminal market

“

E” or coloured Green or Green & Yellow.

• Connect Brown wire to terminal marked “

L” or

coloured Red.

• Connect Blue wire to terminal marked “

N” or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a 13 amp fuse. A15 amp plug must be

protected by a 15 amp fuse, either in the plug or

adaptor or at the distribution board.

If you are in any doubt about the electrical supply to

your machine, consult a qualified electrician before

use.

How to connect an alternative plug

The wires in this

mains lead are

coloured in

accordance with the

following code:

• BLUE

“NEUTRAL” (“N”)“NEUTRAL” (“N”)

“NEUTRAL” (“N”)

• BROWN

“LIVE” (“L”)“LIVE” (“L”)

“LIVE” (“L”)

• GREEN AND YELLOW

“EARTH” (“E”)“EARTH” (“E”)

“EARTH” (“E”)

Disposing of the appliance

When disposing of the appliance please remove the

plug by cutting the mains cable as close as

possible to the plug body and dispose of it as

described above

GREEN &

YELLOW

BROWN

BLUE

13 amp fuse

CROSS-BAR

CORD GRIP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IDTM Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit IDTM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info