Bedienungsanleitung Indesit IHGC 9.4F LM X (Seite 18 von 64) (Alle Sprachen)

685107

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ELECTRICAL CONNECTION

The mains power supply must correspond to the rating indicated on the plate

situated inside the hood. If provided with a plug connect the hood to a socket in

compliance with current regulations and positioned in an accessible area, after

installation. If it not fitted with a plug (direct mains connection) or if the plug is not

located in an accessible area, after installation, apply a double pole switch in

accordance with standards which assures the complete disconnection of the

mains under conditions relating to over-current category III, in accordance with

installation instructions.

WARNING!

Before re-connecting the hood circuit to the mains supply and checking the

efficient function, always check that the mains cable is correctly assembled.

Replacing the power cable

The hood is provided with a special power cable ; if the cable is damaged,

request a new one from Technical Service.

AIR VENT

(for the suction versions)

Connect the hood and discharge holes on the walls with a diameter equivalent to

the air outlet (connection flange).

Using the tubes and discharge holes on walls with smaller dimensions will cause

a diminution of the suction performance and a drastic increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensable length.

! Use a duct with as few elbows as possible (maximum elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! The company declines any responsibility whenever these regulations are

not respected.

FILTERING OR DUCTING ?

! Your cooker hood is ready to be used in suction version.

To use the hood in filtering version the special ACCESSORY KIT must be

installed.

Check on the first pages of this manual if the ACCESSORY KIT is furnished

or must be bought separately.

Note: If furnished, in certain cases, the additional activated carbon filtering

system may be installed on the hood.

Information about the conversion of the hood from suction version to filtering

version is present in this manual.

Ducting version

In this case the fumes are conveyed outside of the building by means of a

special pipe connected with the connection ring located on top of the hood.

CAUTION!

The exhausting pipe is not supplied and must be purchased apart.

Diameter of the exhausting pipe must be equal to that of the connection ring.

CAUTION!

If the hood is supplied with active charcoal filter, then it must be removed.

Filter version

The aspirated air will be degreased and deodorised before being fed back into

the room.

In order to use the hood in this version, you have to install a system of additional

filtering based on activated charcoal.

CONTROLS

The hood is fitted with a control panel with aspiration speed selection control and

a light switch to control cooking area lights.

T1. ON/OFF light switch

T2. Speed 1/OFF switch

T3. 2-speed selection

T4. 3-speed selection

MAINTENANCE

Cleaning

Clean using ONLY a cloth dampened with neutral liquid detergent. DO NOT

CLEAN WITH TOOLS OR INSTRUMENTS. Do not use abrasive products. DO

NOT USE ALCOHOL!

Perimeter aspiration panel

Clean the perimeter aspiration panel with the same frequency as the ant-fats

filter, using a cloth and not too concentrated liquid detergent. Do not use

abrasive substances.

Maintenance of the anti-grease filters

Traps cooking grease particles.

This must be cleaned once a month (or when the filter saturation indication

system – if envisaged on the model in possession – indicates this necessity)

using non aggressive detergents, either by hand or in the dishwasher, which

must be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolor slightly, but this

does not affect its filtering capacity.

To remove the grease filter, pull the spring release handle.

Maintenance of the charcoal filter

It absorbs unpleasant odors caused by cooking.

The saturation of the charcoal filter occurs after more or less prolonged use,

depending on the type of cooking and the regularity of cleaning of the grease

filter.

In any case it is necessary to replace the cartridge at least every four mounths

(or when the filter saturation indication system – if envisaged on the model in

possession – indicates this necessity).The charcoal filter may NOT be washed or

regenerated.

Assembly

Hook the charcoal filter at the back on the metal tongue of the hood first, then on

the front with the two knobs.

Disassembly

Remove the charcoal filter by turning the knobs fixing it to the hood by 90°.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IHGC 9.4F LM X Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info