Bedienungsanleitung Indesit Is 70 CS (Seite 4 von 12) (Englisch)

34677

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Installation

Moulded plug

! The plug must not be used

without the fuse cover in place.

If a replacement fuse

holder/cover is required, it must

be of the same colour coding or

wording as shown on the base of

the plug.

Replacements are available from

authorised dealers.

Changing the plug

The wires in the power cord are coloured in accordance

with the following:

! If the plug being replaced is a non-rewirable type,

then the cut-off plug must be disposed of safely. DO

NOT leave it where it can be inserted into a socket and

create a shock hazard.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this dryer

and fitted only by authorised technicians (see Service).

New or longer power cords are supplied at an extra

charge by authorised dealers.

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a

qualified electrician.

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the

appliance under a work

counter, be sure to leave a

10mm space between the

top and any other objects

on or above the machine and

a 15mm space between the

sides and lateral furnishings

or walls.

This is to ensure proper air circulation.

! Make sure that the back vents are not obstructed.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an

environment that is not damp and has proper air

circulation throughout. Airflow around the dryer is

essential to condense the water produced during the

washing, the dryer will not operate efficiently in an

enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation could be experienced.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

Door Reversal Instructions

The door of your dryer is reversible and can easily be

changed. Exchange diagonally hinge brackets and

blanking screws. Exchange door latch and catch with

their opposite blanking plates (see diagram above).

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. Simply remove the top hose

from its top fitting at the rear of the dryer and plumb the

hose provided to the drain.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

Ensure your hands are dry.

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the socket.

! Do not use extension cords.

! The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if it is exposed to rain or

storms.

! Once installed, the dryers electrical wire and plug must be

within easy reach.

! The power cord must not be bent or squashed.

! The power cord supplied is fitted with a BS1363 plug and a 13

amp BS1362 fuse. If you need to replace the fuse, use only

those rated at 13 amp (13A) and ASTA approved to BS1362.

Door catch

Door latch

Hinge

Green and Yellow

(Earth) wire to terminal

marked ‘E’, symbol ,

or coloured green and

yellow.

13A ASTA approved

fuse to BS1362.

Brown (Live) wire to

terminal marked ‘L’ or

coloured red.

Blue (Neutral) wire to

terminal marked ‘N’ or

coloured black.

Cord clamp

Minimum gap 10mm

Minimum gaps

15mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit Is 70 CS Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info