Bedienungsanleitung Indesit ISL 79 CB (Seite 23 von 24) (Englisch, Holländisch)

70635

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Troubleshooting

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

Empty water light is flashing

but the dryer has only been

running for a short period.

Empty water light is on and

the water container is not full.

The ON/OFF light flashes to

indicate a fault.

Programme finishes and

clothes are damper than

expected.

Possible causes / Solution:

●

The plug is not plugged into the socket, or not making contact.

●

There has been a power failure.

●

The fuse has blown. Try to plug another appliance into the socket.

●

You are using an extension cord? Try to plug the dryer’s power cord

directly into the socket.

●

The door is not closed securely?

●

The PROGRAMMES knob has not been set properly (see Start and

Programmes).

●

The START button has not been pressed (see Start and Programmes).

●

You have set a delayed time (see Start and Programmes).

●

The filter has not been cleaned (see Maintenance).

●

The water container needs emptying? The empty water light is flashing?

(see Maintenance).

●

The condenser needs cleaning? (see Maintenance).

●

The temperature setting is not ideal for the type of fabric you are drying

(see Start and Programmes, and see Laundry).

●

The correct drying time has not been selected for the load (see Laundry).

●

The air intake grille or rear vents are obstructed (see Installation, and see

Maintenance).

●

The items were too wet (see Laundry).

●

The dryer was overloaded (see Laundry).

●

The water container was probably not emptied at the start of the programme.

Do not wait for the empty water signal, always check and empty the

container before starting a new drying programme (see Maintenance).

●

This is normal, the light flashes when the container is full. If the light is on

but not flashing it is just a reminder to empty the container (see Start and

Programmes).

●

If the ON/OFF light flashes together with the Time Delay and High Heat

lights; Or the ON/OFF light flashes together with the Time Delay, Alarm,

High Heat and Empty Water lights, then:

- Turn off and remove the plug. Clean the filter and the condenser

(see Maintenance). Then replace the plug, turn on and start another

programme. If the same combination of lights still flash contact the

Service Centre (see Service).

●

If any other combination of lights flash: Note down the other lights that

are flashing and contact the Service Centre (see Service).

! For safety the dryer has a maximum programme time of 3 hours. If an

automatic programme has not sensed the required final moisture in this time

the dryer will complete the programme and stop. Check the above points

and run the programme again, if the results are still damp, contact the

Service Centre (see Service).

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the

following troubleshooting suggestions:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit ISL 79 CB Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info