Bedienungsanleitung Indesit ISL69C (Seite 18 von 24) (Englisch, Französisch)

46904

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Start and Programmes

Alarm

Available on all programmes and allows the buzzer to

give a signal at the end of the drying cycle, to remind

you that the clothes are ready to be removed.

Press the button and the light will show that the option

is selected.

Post Creasecare

The clothes are occasionally tumbled after the end of

the drying and cool tumble cycles, to help prevent

creases developing should you not be available to

remove the load immediately the programme is complete.

Empty Water Light / Container

(If you have plumbed your dryer to a drain this light

can be ignored, as there is no need to empty the water

container).

When this light is on (not flashing) it reminds you to

empty the water container.

If the water container fills during a programme, the

heater turns off and the dryer does a period of Cool

Tumble then the light flashes and the buzzer sounds.

After this it stops and all 3 progress lights and the 3hr

delay light come on and the empty water light flashes.

You must empty the water container and restart the

dryer or the clothes will not dry. After re-starting the

dryer, the light will take a few seconds to go out.

To avoid this always empty the water container each

time you use the dryer (see Maintenance).

●

Door Opening

Opening the door during a programme will stop the

dryer and have the following effects:

●

All 3 progress lights abd the 3hr delay light come

on.

●

During a delay phase the delay will continue to

count down. The start button must be pressed to

resume the delay programme.

One of the delay lights will flash to show the

current delay setting.

●

The start button must be pressed to resume the

programme. The progress lights will change to

show the current status.

●

During the cool tumble or post creasecare phase

of a drying programme and anytime during an

Airing or Cool Tumble programme, the programme

will finish. Pressing the start button will re-start a

new programme at the beginning.

●

Changing the programmes knob will select a new

programme, after you press the start button. You

can use this to select the Cool Tumble programme

to cool the clothes, if you find them dry enough.

●

Note

If you have a power cut, switch off the power or

remove the plug, press the START button and the

programme will resume.

●

PROGRAMMES knob

! Warning, if after pressing the start button, the

programmes knob position is changed, the new position

will NOT change the programme selected.

! Position 0, turning the knob to position 0 resets and

cancels a programme.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programme knob before

an option can be selected. Not all options are available

for all programmes (see Start and Programmes). If an

option is not available and you press the button, the

buzzer will beep four times. If the option is available

there will be one beep and the option light above the

button lights to confirm the selection.

After the start button has been pressed only the Alarm

option can be changed.

Progress ( Drying, CoolTumble, Post

Creasecare) / Delay (3hr 6hr 9hr 12hr) Lights

When the light above the delay button is on, these lights

flash to indicate the delay time is selected. During other

programmes they indicate the progress of the dryer,

each one comes on as the corresponding phase starts.

Time Delay

The start of some programmes (see Start and

Programmes) can be delayed for up to 12 hours in 3hr

steps. Ensure the water bottle is emptied before setting

a delayed start.

When a delayed start is in progress the light above the

delay button will be on and the selected delay period

light will flash (after the start button has been pressed).

To set a delayed start, press the Time Delay button,

and the light above the button will come on together

with the 3hr delay light. Pressing the button again will

advance the delay setting to 6hr, the 3hr light goes

out and the 6hr light is on. Each time you press the

button the delay setting advances 3 hours, as indicated

by the corresponding light. If the 12hr light is on,

pressing the button again will cancel the delay.

You can also cancel the delay by turning the programmes

knob to 0, wait for the buzzer to beep and then turn

back to your selected programme.

Pre Creasecare

When a delayed start has been selected, the clothes

are tumbled occasionally during the delayed period to

help prevent creases developing.

High Heat

When available this button selects high heat. Press this

button and a high heat setting is selected and the light

above the button comes on. Timed programmes have

a default of low heat, if the light alongside the button is

on then pressing the button selects a low heat setting

and the light goes out.

The Controls

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit ISL69C Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit ISL69C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info