512953
30
Zoom out
Zoom in
Vorherige Seite
1/33
Nächste Seite
8
DK
fig.9
fig.10
INSTALLATION
A
fig.8
Gas supply
Check that the appliance is set for the type of gas available
and then connect it to the mains gas piping or the gas
cylinder in compliance with the applicable norms in force.
This appliance is designed and set to work with the gas
indicated on the label situated on the actual hob. If the gas
supply is different from the type for which the appliance
has been set, replace the corresponding nozzles (provided),
following the instructions given in the paragraph "Adaptation
to different types of gas".
For trouble-free operation, suitable use of energy and a
longer life cycle for the appliance, make sure that the supply
pressure complies with the values indicated in table 1
"Burner and nozzle specifications", otherwise install a
special pressure regulator on the supply pipe in compliance
with current standards and regulations.
Connect in such a way that the appliance is subjected to
no strain whatsoever.
Either a rigid metal pipe with fittings (fig. 8-D) in compliance
with norms must be used for connecting to the nipple union
(threaded - cylindrical ½"G fitting "F") situated at the rear of
the appliance (fig. 8), or a flexible steel pipe with a continuous
wall and fittings (fig. 8-C) in compliance with norms, which
must not exceed 2000 mm in length. Check that the connecting
pipe cannot come into contact with moving parts which could
damage or crush it. For installation with a flexible rubber
pipe, apply the special hose support for liquid gas (fig. 8-A)
or natural gas (fig. 8-B). The gasket "G" (provided) must be
utilised in every type of connection. The two ends of the pipe
must be fastened with the purpose designed pipe collars "E",
in compliance with the norms. The flexible pipe should comply
with the norms, and be specific for the type of gas used. In
addition:
it should be as short as possible, with a maximum length
of 1.5 metres;
it should not be bent or kinked;
it should not be in contact with the rear panel of the appli-
ance or in any case with parts which may reach a tem-
perature of 50°;
it should not pass through holes or slits used for discharg-
ing the oven flue gases;
it should not come into contact with pointed parts or sharp
corners;
it should be easy to inspect along its entire length in order
to be able to check its condition;
it should be replaced before the date printed on the actual
pipe.
Important: A pressure regulator, in compliance with the
applicable norm in force, must be inserted when
connecting to a liquid gas supply (in a cylinder).
Upon completion of installation, check for leaks from the
gas circuit using a soapy solution (never use a flame). Make
sure that the natural gas pipe is adequate for a sufficient
supply to the appliance when all the burners are lit.
Adapting to different types of gas
To adapt the hob to a different type of gas from the factory-
set one (indicated on the rating plate at the top of the hood
or on the packaging), the burner nozzles should be replaced
as follows:
Remove the hob grids and slide the burners off their seats.
Unscrew the nozzles (fig. 9), using a 7 mm socket span-
ner and replace them with nozzles for the new type of gas
(see table 1 "Burner and nozzle characteristics").
Reassemble the parts following the above procedure in
the reverse order.
• On completing the operation, replace the old rating label
with the one showing the new type of gas; the sticker is
available from our Service Centres.
Adjusting the primary air of the burners
The primary air of the burners does not need to be adjusted.
Adjusting the low flame
Turn the tap to the low flame position;
• Remove the knob and turn the adjusting screw, situated to the
right of the tap (fig. 10) until you obtain a regular small flame,
using a screwdriver (loosening the screw increases the height
of the flame, tightening decreases it).
N.B.: In the case of liquid gas, the regulation screw must
be screwed in all the way.
Having obtained the low flame setting required and with the
burner lit, abruptly change the position of the knob several times
from minimum to maximum and vice versa and check that the
flame does not go out.
In appliances fitted with the safety device (thermocouple), should
the device fail to work with the burners set to the low flame
setting, increase the low flame setting of the same on the ad-
justing screw.
Once the adjustment has been made, remount the seals on the
by-passes using sealing wax or similar.
30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

indesit-kp-648-ms

Suche zurücksetzen

  • zeitschaltuhr des Backofens funktioniert nicht mehr. wo bekommt man Ersatz, wie wechselt man?
    Eingereicht am 23-3-2023 16:47

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Indesit KP 648 MS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info