Bedienungsanleitung Indesit ta 2 s (Seite 14 von 68) (Englisch, Holländisch, Französisch, Italienisch, Polnisch)

345546

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Tips on Saving Energy

- Install the Appliance Properly

In other words, away from sources of heat and direct sun-

light, in a well ventilated room complying with the minimum

distances indicated in the paragraph entitled, “ Installation/

Ventilation.”

- Use the Right Temperature Setting

A setting which is too cold increases energy consumption.

- Do not Overfill

To conserve food properly, the cold air must circulate freely

within the refrigerator. If it is overfilled, this will prevent proper

air circulation, forcing the compressor to work continuously.

- Close the Doors

Open your refrigerator as little as possible because each time

you do so you loose much of the cold air. To raise the tem-

perature to the proper level again, the motor must work for

a long time, consuming energy.

- Keep an Eye on the Seals

Keep the seals clean and make sure that they adhere well to

the door. This alone will ensure that no cold air escapes.

- No Hot Foods

A hot pot or pan placed in the refrigerator immediately raises

the temperature several degrees. Let hot cookware and food

cool to ambient temperature before placing them in the re-

frigerator.

- Defrost the Freezer

Check the thickness of the frost on the walls of the freezer

and immediately defrost it if the layer of frost is too thick.

(see the section entitled, “Keeping your Appliance in Shape”).

Ice tray

This new concept of ice tray is an exclusive Merloni patent.

The fact that they are situated on the inner door of the freezer

compartment ensures greater ergonomics and cleanliness:

the ice no longer comes into contact with the food placed

inside the freezer compartment; furthermore, the dripping

of the water during filling is avoided (a lid to cover up the

hole after filling with water is also provided).

Instructions for use (Fig. 2)

Fill up the tray with water via the special hole up to the level

indicated (MAX WATER LEVEL), taking care not to exceed

it: inserting more water than is necessary will lead to the

formation of ice which could obstruct the exit of the ice

cubes.

If you have used an excessive amount of water, you will

have to wait until the ice has melted, empty out the tray

and re-fill it with water.

Once you have filled the ice tray up with water through the

hole indicated, turn it by 90 °. Thanks to the connected

compartments, the water fills up the special shapes, after

which you can cover the hole up with the special cap and

place the ice tray in the inner door of the freezer compartment.

Fig. 2

Once the ice has formed, all you need to do is to knock the

tray against a hard surface so that the ice cubes come away

from their housing and come out of the same hole used to

fill the tray with water. To make it easier for the ice cubes to

come out, wet the outside of the tray.

WARNING: every time you fill up the ice tray with water ,

make sure that the same is completely empty and that there

are no traces of ice left inside it.

The minimum time required for ice to form well is

approximately 8 hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit ta 2 s Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info