Bedienungsanleitung Indesit w 103 (Seite 11 von 16) (Englisch)

304047

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

When the new

washer arrives

Installation and removal

Whether new or just transported to a new house,

installation is extremely important for the correct

functioning of your washing machine.

Water pipe inlet at the top right.

Connecting the drain hose

The drain hose (hooked pipe) is

secured to the rear of the machine

by support clips and may be

routed to right or left as required.

The hook to be used in case the drain

hose ends at a height below 60 cm.

The drain hose should be placed

in a stand pipe with a minimum

internal diameter of 38 mm (1½

inches) or it can be positioned over

a sink or it can be connected as

shown in Fig. A. The height of

stand pipe or sink should be

between 60 and 100 cm (24 and

40 inches). Care must be taken

that the hose is not obstructed,

twisted, submerged or kinked. If

the hose is connected with an

airtight joining, provision should be

made to prevent syphoning.

The guide for draining into tubs and

sinks.

Fig. )

Electric connection

Your appliance is now supplied

with a 13 amp fused plug it can

be plugged into a 13 amp socket

for immediate use. Before using

the appliance please read the

instructions below.

WARNING - THIS APPLIANCE

MUST BE EARTHED.

THE FOLLOWING OPERATIONS

SHOULD BE CARRIED OUT BY A

QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a

13 amp ASTA approved fuse to

BS 1362 should always be used,

and the fuse cover re-fitted. If the

fuse cover is lost, the plug must

not be used until a replacement

is obtained.

After removing the appliance from

its packaging, check that it is

intact. If in doubt, contact a

qualified technician immediately.

The inside of the machine is

supported, for transportation, by

3 screws on the back panel.

Before using the washing

machine, remove the screws,

remove the spacers together with

the rubber tubes attached to them

(keeping all the parts) and use the

plastic plugs provided to fill in the

holes.

Important: Use the cap (provided)

to close the 3 holes which housed

the stop pin, situated in the right-hand

part of the lower back of the

washing machine.

Part A must not be removed.

Levelling

The washing machine must be

levelled appropriatey in order to

guarantee its correct functioning. To

level the appliance, the front feet

must be adjusted; the angle of

inclination, measured according to

the worktop, must not exceed 2°.

When placed on carpet, make sure

the ventilation is not reduced.

The front feet are adjustable.

Connection to the water

mains

Both hot and cold water supplies

are preferable and they should be

between 34.5kN/m²(5lb/in²) and

1034.2kN/m² (150lb/in²) pressure.

The hose having the red end fitting

should be encountered between

the hot supply and the threaded

connection adjacent to the letter H

on the rear of the machine. The

hose having the white end fittings

should be connected between the

cold supply and the threaded

connection adjacent to the letter C

on the rear of the machine.

Remember to insert a sealing

washer at each connection to

ensure watertight joints. Do not

overtighten the connections by

using tools -hand tight is sufficient

to prevent leaks. It is generally more

convenient to have these supplies

away from the sink taps. Where

no suitable hot water supply is

available or it does not meet these

requirements, both inlet hoses may

be connected to a cold supply by

using two taps etc., or a «T»

junction on the plumbing however,

use of cold water only will increase

programme times.

Note: the maximum temperature

should not exceed 70°C (158°F).

The rubber gasket .

Connect the inlet hose to the

threaded connector on the

machine rear.

Warning!

The company denies all

liability if and when these

norms are not respected.

Plastic bags, expanded

styrofoam, nails and other

packaging parts are not

children’s toys, and are

potentially dangerous.

Retain the transit screws,

spacers and washers.

Should you move house

then these should be

replaced to support the

inside of the machine to

prevent damage when

transporting the machine.

Instructions for installation and use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit w 103 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit w 103

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info