Bedienungsanleitung Indesit widl 106 (Seite 2 von 12) (Englisch)

304495

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

 Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the Washer-dryer to inform the

new owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the Washer-dryer.

2. Check whether the Washer-dryer has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the four

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance (see

figure).

4. Seal the gaps using the plastic plugs provided.

5. Use the plug provided to seal the three holes

where the plug was housed, situated on the lower

right-hand side on the rear of your appliance.

6. Keep all the parts: you will need them again if the

Washer-dryer needs to be moved to another

location.

 Packaging materials are not children's toys.

Levelling

1. Install the Washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet (see figure);

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the Washer-

dryer.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply

pipe to the water mains

using a gas 3/4

attachment, fitting the

rubber gasket and the

filter supplied with the

appliance and ensuring

that they are fimly

tightened to the taps.

The water supply marked

C must be connected to the cold water tap; the pipe

marked H must be connected to the hot water tap.

Both pipes may be connected to the cold water tap

using the special Y connection with multiple

attachments, supplied with the appliance (see figure).

Before making the connection, allow the water to run

freely until it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the Washer-dryer,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the

hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit widl 106 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info