Bedienungsanleitung Indesit YT M08 71 R (Seite 4 von 4) (Englisch)

684554

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

TROUBLESHOOTING

Before contacting the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in few minutes

Malfunction

Possible cause

Solution

The tumble

dryer does not

turn on.

The plug is not inserted into the socket.

Insert the plug into the socket.

The plug is faulty.

Try to plug another appliance in the same socket. Do not use

connecting electrical devices to the socket, as adapters or extensions

A power failure occurred. Await the reactivation of the power supply.

The tumble

dryer does not

start

The door is open.

Close the door.

A time delay for the cycle start was set.

For machines equipped with this function: await the end of the delay

set or switch the machine o to reset it. Refer to the section Options.

The button Start/Pause was not pressed to start

the program.

Press the button Start/Pause.

The function Key Lock was enabled (in case of

machines equipped with this option).

Refer to the option section and, if the Key Lock is present, disable it.

Switching the machine o is not enough to disable this option.

The drying

times are very

long

An appropriate maintenance was not carried

out.

Refer to the section Care & Maintenance and perform the operations

described.

The programme, the time and/or the drying

level set are not suitable for the type and the

amount of load inserted into the dryer.

Refer to the section programmes and options to  nd the programme

and the options most suitable for the type of load.

The garments are too wet.

Carry out a washing cycle with higher spin speed to remove as much

water as possible.

The dryer may be overloaded.

Refer to the programme section to check the max. load for each

programme.

The programme

did not end.

A power failure occurred might have occurred.

In case of power failure, it is necessary to press the button Start/Pause

to restart the cycle.

Lights on or  ashing

Water tank The water tank is full. Emtpy the water tank. Refer to the section Care & Maintenance.

Door  lter

and/or bottom

 lter*

Failure of the air  ow necessary for machine

operation.

Clean the door  lter and the bottom one and check whether air

intake is free. Carrying out these operations improperly may cause

damages.

Bottom  lter* The bottom  lter requires cleaning. Clean the bottom  lter. Refer to section Care & Maintanence.

DEMO

The cycle lasts

few minutes.

The dryer is in DEMO mode. The DEMO

indicator is on.

Disable the DEMO mode. The following actions must be carried out

in sequence, without breaks. Switch the machine on and then switch

it o again. Press the Start/Pause button until the buzzer is heard.

Switch the machine on again. The “DEMO” indicator  ashes and then

turns o .

The presence

of wrench

symbol signals a

malfunction.

The machine sensors detected a failure.

Switch the dryer o and unplug it. Open the door immediately and

pull laundry out, to allow the heat to dissipate. Wait for about 15

minutes. Reconnect the dryer to the power supply, load the laundry

and restart the drying cycle. If the problem still occurs, contact

the After-Sales Service Centre and communicate the letters and

digits  ashing on the display.

For instance: F3 and E2

*Note: some models are self-cleaning and not equipped with bottom  lter. Please refer to the section Care & Maintenance.

You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:

• Visiting our website - docs.indesit.eu

• Using QR Code

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When

contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.

THANK YOU FOR BUYING A INDESIT PRODUCT.

In order to receive a more complete assistance,

please register your product on

www.indesit.eu/register

Quick guide

Before using the appliance carefully read the Safety Instructions.

xxxxxxxxxxxx

xxxx

Some LEDs  ashing at the same time signal a malfunction. Carry out the procedures described in this page.

Swith the dryer o and unplug it. Open the door immediately and pull landry out, to allow the heat to dissipate.

Wait for about one hour. Reconnect the dryer to the power supply, load the laundry and restart the drying cycle.

If the problem still occurs, contact the After-Sales Service Centre and communicate the letters and digits  ashing on

the display e.g.:

First and second horizontal LED of alarm lights.

First vertical LED of option buttons.

Memo

Start

delay

Dryness

level

Drying

Time

Crease

Care

Sound

3 sec

Refresh

Technical Wear

Xpress 45’

Shirt

Wool

Duvet

Synthetics

Eco Cotton

Eco Synthetics

Delicate

Jeans

Baby

Sport

Sport shoes

Indesit_Tilt_Mono_Dryer_M10

Dry time

120

min

60 min

30 min

15 min

Delicates

Wool

Cotton

Cupboard dry +

Cupboard dry

Hanger dry

Iron dry

Cupboard dry

Hanger dry

Iron dry

Synthetics

Eco cotton

08-05-2017

Indesit_Tilt_Mono_Dryer_M08

Auto

drying

Multilev.

option

Multilev.

option

Option Option

Timed

drying

Start

delay

Option

3 sec

Wool

Daily cotton

Anti odour

Duvet

Sport

Rinse + Spin

Spin + Drain

Daily synthetics

Coloureds

Delicates

Rapid 30

min

Cotton

Synthetics

Mixed

Eco cotton

0 3

400

800

1200

1400

16-05-2017

Indesit_Tilt_Modul_Dryer_M21

Cotton

DEMO

Indesit YT M08 71 R Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit YT M08 71 R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info