Bedienungsanleitung Infiniti M45 - 2007 (Seite 377 von 390) (Englisch)

626197

377

Zoom out

Zoom in

Vorherige Seite

1/390

Nächste Seite

A vehicle equipped with All-Wheel Drive

(AWD) should never be tested using a two

wheel dynamometer (such as the dyna-

mometers used by some states for emis-

sions testing), or similar equipment. Make

sure you inform test facility personnel

that your vehicle is equipped with AWD

before it is placed on a dynamometer. Us-

ing the wrong test equipment may result

in transmission damage or unexpected

vehicle movement which could result in

serious vehicle damage or personal in-

jury.

Due to legal requirements in some states/

areas, your vehicle may be required to be

in what is called the “ready condition” for

an Inspection/Maintenance (I/M) test of

the emission control system.

The vehicle is set to the “ready condition”

when it is driven through certain driving

patterns. Usually, the “ready condition”

can be obtained by ordinary usage of the

vehicle.

If a powertrain system component is re-

paired or the battery is disconnected, the

vehicle may be reset to a “not ready con-

dition”. Before taking the I/M test, check

the vehicle’s inspection/maintenance test

readiness condition. Push the ignition

switch to the ON position without starting

the engine. If the Malfunction Indicator

Lamp (MIL) comes on steady for 20 sec-

onds and then blinks for 10 seconds, the

I/M test condition is “not ready”. If the

MIL does not blink after 20 seconds, the

I/M test condition is “ready”.

If the MIL indicates the vehicle is in a “not

ready” condition, drive the vehicle

through the following pattern to set the

vehicle to the “ready condition”. If you

cannot or do not want to perform the

driving pattern, an INFINITI dealer can

conduct it for you.

WARNING

Always drive the vehicle in a safe and pru-

dent manner according to traffic conditions

and obey all traffic laws.

1. Start the engine. Allow the engine to

idle until the engine coolant tempera-

ture gauge needle points between the

C and H (normal operating tempera-

ture).

2. Accelerate the vehicle to 55 MPH (88

km/h), then quickly release the accel-

erator pedal completely and keep it re-

leased for at least 10 seconds.

3. Quickly depress the accelerator pedal

for a moment, then drive the vehicle at

a speed of 53 to 60 MPH (86 to 96

km/h) for at least 9 minutes.

4. Stop the vehicle. Leave the engine

running.

5. Accelerate the vehicle to 35 MPH (55

km/h) and maintain the speed for 20

seconds.

6. Repeat steps 4 and 5 at least 10 times.

7. Accelerate the vehicle to 55 MPH (88

km/h) and maintain the speed for at

least 3 minutes.

8. Stop the vehicle. Place the transmis-

sion gear selector lever in the “P” or

“N” position.

9. Turn the engine off.

10. Repeat steps 1 through 8 at least one

more time.

If step 1 through 7 is interrupted, repeat

the preceding step. Any safe driving mode

is acceptable between steps. Do not stop

the engine until step 7 is completed.

READINESS FOR INSPECTION/

MAINTENANCE (I/M) TEST (US only)

Technical and consumer information 9-19

w 06.12.8/Y50-D X

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Infiniti M45 - 2007 Seite 377

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info