Bedienungsanleitung InFocus in2114 (Seite 34 von 45) (Englisch)

216221

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Using Network Functions (IN2114 & IN2116 only)

IMPORTANT: To enable network functions at all times (even when the pro-

jector is powered off), the Network item in the Always-On Functions sub-

menu in the Setup menu must be set to Yes (not No).

Projector network functions include:

• Configuring and controlling the projector via a web browser.

• Failure and warning alerts via email.

• Projector Management via SNMP.

• Controlling the projector via Scheduling.

NOTE: Projector web pages and emails sent by the projector are always dis-

played in English language.

Before using the network functions

To use the network functions of the projector, the projector must be config-

ured to suit your network. Consult with your network administrator before

connecting the projector to your network; incorrect network configuration

of the projector may cause problems on your network.

Connect the Network Cable

Properly connect projector to the network, then configure the following set-

tings.

If Using a Network with DHCP Enabled:

1 Use the projector's remote control or keypad to select the Network item

in the projector's Setup menu.

2 If DHCP is off, select it to turn it on.

If Using a Network that Does Not have DHCP Enabled:

1 Use the projector's remote control or keypad to select the Network item

in the projector's Setup menu.

2 If DHCP is on, select it to turn it off.

NOTE: If you still don’t see an IP address, go to the projector’s Setup menu,

select Network, then turn on Show Network Messages. After exiting the

menu press the Source button again.

3 Select IP Address. This will highlight the first of the four octets in the IP

address. Press Up or Down to change the value, then press Select or Right

when done to move to the next octet. Repeat until you have changed all

four octets in the IP address.

4 Repeat the above for Subnet Mask, Default Gateway, and other settings

that are in IP address format (to assign or change the Host Name, see

Network Settings Page below).

Configuring and Controlling the Projector via a Web Browser

You can adjust or control the projector via a network from a web browser

on a computer that is connected to the same network as the projector.

NOTES:

• To access the projector’s web pages, the projector must be connected to

the network and connected to AC power (and if you want to access the

web pages even when the projector is powered off, make sure that the

Network item in the Always-On Functions submenu is set to Yes).

• JavaScript must be enabled in your browser to use the projector web

pages properly. If JavaScript is disabled, see the Help files for your web

browser for details on how to enable it.

• If no operations are performed in the web browser for approximately

ten minutes, the system will automatically log you off.

Logging in

To log into the projector web pages, follow these steps:

1 Make sure the projector is connected to the network and connected to

AC power.

2 If you don't know the projector's IP

address, turn on the projector. After the

projector starts up, if its IP address is not

shown, press the Source button to view the IP address.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

InFocus in2114 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von InFocus in2114

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info