Bedienungsanleitung InFocus IN2124A (Seite 51 von 60) (Englisch)

544153

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

LiteBoard™ Wand

The optional LiteBoard™ Wand (p/n HW-LBWAND-02), when combined with

the LiteBoard Wand dongle (p/n HW-LBRADIO), works like a wireless mouse -

but one that works in midair, not on your desktop. Just hold the wand in your

hand, and point it at the projected image to point, click and drag. The wand works

with all your software, just like a regular mouse.

Charging the Wand’s Battery

When the wand’s red battery light starts to blink, its internal battery is low (if the

battery is fully discharged, you won’t be able to turn the wand on by pressing its

tip, left or right mouse buttons).

To charge the battery, open the flap on the right side of the wand to expose the

wand’s USB connector. Then connect a USB cable between the wand and a USB

power adapter (not included), or a computer (if connecting to a computer, make

sure the computer is powered on). The battery light will stay on while the battery

is charging, then it will turn off when the battery is fully charged.

When charging is finished, you can disconnect the USB cable (or keep the cable

connected and use the wand while it’s charging).

NOTE: 5-10 minutes of charging is enough for about an hour of wand use. A full

charge will take 3-4 hours and will allow 20-40 hours of non-stop wand use. A fully

charged, new wand will hold a charge in standby for up to 3 weeks.

Caution: The lithium battery is only rechargeable, and is not user serviceable or

user replaceable.

Caution: Always use a USB cable and power adapter (or your computer) to charge

the wand.

How to Use the Wand

1 Connect the LiteBoard™ Wand dongle (p/n HW-LBRADIO) to the LiteBoard

Radio connector of the projector.

2 The projector needs to be powered on and connected to your computer.

3 Connect the projector and your computer with a USB cable (USB Type A to

USB Type B).

4 Connect the projector and your computer with a VGA cable.

5 Make sure the wand's battery is charged or charging.

6 Turn on the projector and make sure it's displaying the computer's screen -

set the source to Computer 1 or Computer 2 (press the source button on the

projector or its remote if needed - you may need to press it several times).

7 Enable the LiteBoard™ Wand in the Advanced Menu > Setup > Keypad/

Remote menu.

8 Turn on the wand by pressing its tip, left or right mouse button - 2 blinks of

the blue status light means the wand is searching for a connection. When

connected the light will be lighted continuously.

9 Point the wand at the screen to point, click, and drag - just like a normal

mouse.

NOTE: When you’re done, set the wand aside and make sure it isn’t pointing at

the screen; it will turn itself off automatically after 1 minute.

MOLEX

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

InFocus IN2124A Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von InFocus IN2124A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info