Bedienungsanleitung InFocus IN5122 (Seite 85 von 97) (Englisch)

476237

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Maintenance

Lamp warning

Replacing the lamp (continued)

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►

The projector uses a high-pressure mercury glass lamp. The lamp

can break with a loud bang, or burn out, if jolted or scratched, handled when hot, or

worn over time. Note that each lamp has a different lifetime, and some may burst or

burn out soon after you start using them. In addition, if the bulb bursts, it is possible

for shards of glass to y into the lamp housing, and for gas containing mercury and

dust containing ne particles of glass to escape from the projector’s vent holes.

►About disposal of a lamp: This product contains a mercury lamp; do not put

it in the trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org (in the US).

• For product disposal, consult your local government agency

or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

WARNING

• If the lamp should break, unplug the power cord from the outlet, and make

sure to request a replacement lamp from your local dealer. Note that shards of

glass could damage the projector’s internals, or cause injury during handling, so

please do not try to clean the projector or replace the lamp yourself.

•

If the lamp should break, ventilate the room well, and make sure not to inhale the gas

or ne particles that come out from the projector's vent holes, and not to get them into

your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power cord,

then wait at least 45 minutes for the lamp to cool sufciently.

Handling the lamp

when hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover when the projector is suspended from a ceiling.

This is dangerous, since if the lamp’s bulb has broken, the shards will fall out

when the cover is opened. In addition, working in high places is dangerous, so

ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. When replacing the

lamp, make sure that the screws are screwed in firmly. Loose screws could

result in damage or injury.

• Use only the lamp of the specied type. Use of a lamp that does not meet the

lamp specications for this model could cause a re, damage or shorten the life of

this product.

• If the lamp breaks soon after the rst time it is used, it is possible that there

are electrical problems with the projector. If this happens, consult your local

dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst

during use.

• Using the lamp for long periods of time can cause it to darken, not to light

up or to burst. When the images appear dark, or when the color tone is poor,

please replace the lamp as soon as possible. Do not use old (used) lamps; this

can cause breakage.

Disconnect

the plug

from the

power

outlet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

InFocus IN5122 Seite 85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von InFocus IN5122

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info