Bedienungsanleitung InFocus IN5542 (Seite 20 von 104) (Englisch)

549906

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

● The projector uses a high-pressure mercury glass lamp. The lamp can break with a

loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon

after you start using them. In addition, when the bulb bursts, it is possible for shards of

glass to fly into the lamp housing, and for gas containing mercury to escape from the

projector’s vent holes.

● About lamp disposal: This product contains a mercury lamp; do not put it in a trash.

Dispose of it in accordance with environmental laws.

- For lamp recycling, go to www.lamprecycle.org (in the US).

For product disposal, contact your local government agency or www.eiae.org (in the

US) or www.epsc.ca (in Canada)

For more information, call your dealer.

Disconnect the

plug from the

power outlet

● If the lamp should break (it will make a loud bang when it does),

unplug the power cord from the outlet, and make sure to request a

replacement lamp from your local dealer. Note that shards of glass

could damage the inside of the projector, or cause injury during

handling, so please do not try to clean the projector or replace the

lamp yourself.

● If the lamp should break (it will make a loud bang when it does),

ventilate the room well, and make sure not to breathe the gas that

comes out of the projector vents, or get it in your eyes or mouth.

● Before replacing the lamp, turn the projector off and unplug the

power cord, then wait at least 45 minutes for the lamp to cool

sufficiently. Handling the lamp while hot can cause burns, as well as

damaging the lamp.

● Never unscrew except the appointed (marked by an arrow) screws.

● Do not open the lamp cover while the projector is suspended from

a ceiling. This is dangerous, since if the lamp’s bulb has broken, the

shards will fall out when the cover is opened. In addition, working in

high places is dangerous, so ask your local dealer to have the lamp

replaced even if the bulb is not broken.

● Do not use the projector with the lamp cover removed. When

replacing the lamp, make sure that the screws are screwed in firmly.

Loose screws could result in damage or injury.

● Use only the specified lamp type.

● If the lamp breaks soon after the first time it is used, it is possible

that there are electrical problems elsewhere besides the lamp. If this

happens, contact your local dealer or a service representative.

● Handle with care: jolting or scratching could cause the lamp bulb to

burst during use.

● Using the lamp for long periods of time, could cause it to darken, not

to light up or to burst. When the pictures appear dark, or when the

color tone is poor, please replace the lamp as soon as possible. Do not

use old (used) lamps; this is a cause of breakage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

InFocus IN5542 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von InFocus IN5542

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info