Bedienungsanleitung InFocus in5554L (Seite 35 von 57) (Englisch)

549900

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Maintenance

Cleaning the lens

1 Turn the projector off and unplug the power cord.

2 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

• Avoid using an excessive amount of cleaner, and don’t apply the cleaner

irectly to the lens. Abrasive cleaners, solvents or other harsh chemicals

might scratch the lens.

3 Lightly wipe the cleaning cloth over the lens in a circular motion.

WARNINGS:

• Turn the projector off and unplug power cord before cleaning any part of the

ojector.

• Do not open any cover on the projector, except the lamp cover or projector

p cover.

• Do not attempt to service this product yourself as opening and removing

covers will void the warranty and may expose you to dangerous voltage and

other hazards. Refer all servicing to qualified service personnel.

Replacing the projection lamp

The lamp hours timer counts the number of hours each lamp has been in use.

When the lamp time has expired, the Lamp LED (Lamp1 or Lamp2) on top of the

projector will light solid red.

• NO

TE: Be sure to use the InFocus lamp module designed for this projector.

You can order new lamps from www.infocus.com (in select areas), your

retailer or your dealer. Only genuine InFocus lamps are tested for use

in this projector. Use of non InFocus lamps may cause electrical shock and

fire, and may void the projector warranty. InFocus is not liable for the

performance, safety or certification of any other lamps.

WARNINGS:

• The projector uses two high-pressure mercury glass lamps. The lamps may

ail prematurely or rupture with a popping sound if jolted, scratched, or

handled while hot. The risk of lamp failure or rupture also increases as the

lamp age increases; it is recommended that both lamps be replaced

simultaneously when a Lamp LED (Lamp1 or Lamp2) is solid red.

• To avoid burns, allow the projector to cool for at least 60 minutes before you

eplace the lamps.

• Unplug the power cord before replacing the lamps.

• Do not drop the lamp modules. The glass may shatter and cause injury.

• Do not touch the glass surface of the lamp modules. Fingerprints can obscure

ojection sharpness and may cause the glass to shatter.

• Be extremely careful when removing the lamp modules. In the unlikely event

tha

t a lamp ruptures, small glass fragments may be generated. Although the

lamp modules are designed to contain most of these fragments, use caution

when removing them.

• Before replacing a ruptured lamp, clean the lamp compartment and dispose

cleaning materials. Wash hands after lamp replacement.

• When replacing the lamps while the projector is ceiling-mounted, wear

rotective eyewear to prevent eye injury.

• Hg – Lamp contains mercury. Manage in accordance with local

disposal laws. See www.lamprecycle.org.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

InFocus in5554L Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von InFocus in5554L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info