Bedienungsanleitung Infresco Dimmer 6Kw (Seite 2 von 2) (Englisch)

118456

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

INTRODUCTION

The Infresco has been designed specifically to work with Infra Red Heaters, with a rating of 4kW it

will allow you to control a variety of heating and lighting solution.

The Infresco has a 1 to 10 step setting allowing you to find the optimum comfort setting in you

specific area. With energy saving a major factor in the design brief, once the Infresco is switched

on it will automatically manage the heating system. With a built in temperature sensor only

allowing the unit to switch on when required and a PIR that will detects a requirement for the

heater to switch on only when needed. An optional remote control allows for the unit to be fitted

out of the way so safety is paramount. The Infresco has a built in soft start function which will add

up to an additional 30% life to your heater lamp.

APPLICATIONS

Any application were high inrush current is an issue or control is required. Typical use is for Infra Red

Heating lamps, Garden lighting

FEATURES

Soft Start – up to 30% extended life of Lamp

Variable Control – Ability to find comfort level

Simple Installation – Ability to plug directly in 13A Plug with up to 3kW load

Energy Saving – Automated system. (Only heat when required)

Temperature Monitoring – If ambient temperature is above preset the Infresco unit remains

switched off

SAFETY FIRST

Please read these instructions before installing and operating this product. (See warning for

additional information).

Installation

The ideal site for the PIR to be mounted is approximately 2.5 + Meters of the floor. Ceiling

mounting is preferred but not essential

The PIR must not be mounted.

• Directly in line of the lamps output

• Highly reflective surfaces

• Radiators or other thermostatically controlled heaters

• Open door ways with people walking past

Commissioning

NOTE: On switch on the PIR takes 60 seconds to set before detection takes place

NOTE: The PIR continues to monitor the area and will reset to the set time every time it detects

movement.

Before testing ensure the wiring is correct. The temperature trip point has already been preset at

the factory. The timer is preset to 5 minutes.

The expected detection area can now be “walked tested” using the diagram shown in mind. The

area should be crossed in various directions to ensure coverage is as expected.

Display Features

Display shows ‘t’ The Infresco is turned OFF as the ambient temperature

is above the trip level set by TEMP. SET.

Display shows ‘F’ The Infresco is set to FULL output.

Display decimal point pulses The PIR input is waiting to be enabled i.e. no movement.

Display decimal point fully on The Infresco is in Standby mode pressing the remote

control POWER button will toggle the power ON and OFF.

You can check the remote control is transmitting by observing the decimal point flashing rapidly.



UijthovenInfrarood

Nijverheidstraat31

4261TKWijkenAalburgTheNetherlands

Phone:0031416532724

Fax:0031416532719

E‐mail:info@uithoven.nl



Web:www.terrastopper.nl



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Infresco Dimmer 6Kw Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info