522371
22
Zoom out
Zoom in
Vorherige Seite
1/89
Nächste Seite
24 User Manual
[MENU] + "MENU" + [ENTER] +"ROUTE" + [ENTER] + "REPORT" + [ENTER]
+ [L
OCATE]
The Route Report page is closed and the chart is centered over the first Waypoint
of the selected Route.
Sending Route
To transmit the Active Route information onto the NMEA output port.
[MENU] + "MENU" + [ENTER] +"ROUTE" + [ENTER] + "SEND" + [ENTER]
The NMEA WPL & RTE messages are sent to the output port.
Receiving Route
To save Route information received from the NMEA input port.
[MENU] + "MENU" + [ENTER] +"ROUTE" + [ENTER] + "RECEIVE" + [ENTER]
The received route is saved on the Active route, overwriting it. The NMEA WPL &
RTE messages are sent to the input port.
3.3 GOTO FUNCTION
This functions allows you to place the destination point and immediately start
navigating to it.
Goto Cursor
Place the cursor on the desired location + [GOTO] + "CURSOR" + [ENTER]
The destination is placed at the cursor position and you are now navigating to it.
It is a temporary User Point that will be removed when the navigation is stopped.
If the fix is received, the destination is placed on the desired location, otherwise
a warning message is shown. If the destination is already placed, it is possible to
remove the existing destination and place a new one on the cursor position.
Goto Mark on the Chart page
Place the cursor on any existing Mark + [GOTO]
Goto Mark using the User Points List
[GOTO] + "MARK" + [ENTER] + select the desired User Point + [GOTO]
Goto Route using the Select Route menu
[GOTO] + "ROUTE" + [ENTER] + select one of the existing Routes + [ENTER]/
[GOTO]
The destination is placed on the first Waypoint of the selected route and then the
Route Following function is activated.
Stopping Navigation
If the destination has been placed, to remove it:
[GOTO] + [DELETE]
otherwise, to remove the current destination and place a new one at cursor position:
Place the cursor on location to navigate to + [GOTO] + [NEW] + [ENTER]
3.4 USING TRACK
A very useful feature of the chart plotter, is the ability to store and display exactly
where the boat has been. This feature, referred to as Tracking, can provide in-
valuable information about the effect of tide and wind influence on the boat's
progress as well as giving an indication of the helmsman's performance.
When this limit has been reached, the oldest points are deleted and overwritten
by the newest ones.
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Interphase CHART MASTER 11 CV plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info