522371
51
Zoom out
Zoom in
Vorherige Seite
1/89
Nächste Seite
53
User Manual
Master Chart Plotter
Operating mode
To select the Master mode follow the procedure:
[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "C-LINK" +
[ENTER] + "Primary Station" + [ENTER]
Master mode is the default factory setting. All regular chart plotters’ functions are
allowed. As soon as the Destination is placed, the master chart plotter will start
transmitting all C-Link navigation data,
In Master mode the C-Link navigation data received from the NMEA port is ig-
nored. So, if the two chart plotters are both operating in Master mode, the C-Link
navigation data sent by the other Chart Plotter never processed. Under such
condition if the navigation is activated on one of the two Chart Plotters, a warning
message will be shown to notify that the C-Link navigation data will be ignored by
the other Chart Plotter.
Slave Chart Plotter
Operating mode
To select the Slave mode follow the procedure:
[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "C-LINK" +
[ENTER] + "Secondary Station" + [ENTER]
When Slave mode is set, the chart plotter cannot manipulate the C-Link naviga-
tion data anymore.
Stop current navigation
If the navigation was already active, it will be disabled as soon as Slave mode is
set. An appropriate warning message will be shown to notify that the Navigation
is already active and to confirm whether Slave mode can be set.
Inhibit Navigation operation
As soon as Slave mode is set, the destination cannot be placed anymore either
the C-Link navigation data is received from the Master or not. Also, when the C-
Link navigation data is received from the Master, it will not be allowed to deacti-
vate the Navigation.
Inhibit Route following
While navigating to the route received from the Master the destination is reached
(either applying distance or perpendicular criteria), the destination will not be
moved to the next waypoint on the route.
MOB handling
If the Navigation to the external destination is active and the MOB key is pressed
on the Slave Chart Plotter, the MOB is placed but the navigation to the MOB is not
activated.
Notes
While navigating to the external destination the Operating Mode is switched to
Master mode, the navigation to the external destination will be terminated. An
appropriate warning message will be shown to notify that the Navigation to the
external destination is active and to confirm whether Slave mode can be set.
Setting Slave mode, the C-Link navigation data will be deleted.
The C-Link navigation data are deleted at Power Off.
C-Link navigation data: Acquisition and Display
As soon as the C-Link navigation data is received, the Slave parses the information
received and executes the relative actions depending on its current working status.
Note When the Navigation to the external Destination is activated, the Slave Chart
Plotter will show all relevant C-Link navigation data exactly like when the
51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Interphase CHART MASTER 11 CV plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info