Bedienungsanleitung Interphase CHART MASTER V6 (Seite 42 von 89) (Englisch)

522363

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

44 User Manual

[MENU] + "SETUP" + [ENTER] + "COMPASS" + [ENTER]

Bearings : Selects either degrees magnetic or degrees true. If magnetic readings are

selected the variation is computed automatically for every zone as soon as the

chart is displayed.

Variation : It is possible to calculate the Magnetic Variation in an Automatic or Manual

mode, by inserting the step for calculation of Magnetic Variation.

Calibration : The variation table is used to match magnetic value readout on the chartplotter

comparable with the value given by the compass of the boat. In other words,

since the compass of the boat must be compensated (due to the iron masses,

...), we use the same values given by the chartplotter. This means that, for

example, if the BRG to the next Waypoint readout in the chartplotter display is

"X" Mag degree, if you steer the boat reading "X" Mag degree from the compass,

you are driving well toward the next Waypoint.

4.7 INPUT/OUTPUT SETUP

GPS Connection CM V6/169CS/7MX/7CXS/11CV+/11CVS+

Connects the GPS to the GPS Port (serial Port 3). To choose your preferred

setting follow the procedure:

[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 3 In-

put" + [ENTER] + "NMEA-4800-N81-N" + [ENTER]

GPS Setup Menu

To set your desired configuration for the connected GPS.

Internal GPS : CM V6i/169CSi/7Mi/7Ci Enables or disables the Internal GPS.

Restart GPS : Restarts all GPS processes. Once executed, the message "Done" is shown.

Diff. Corr. Source : Sets what kind of Differential Correction will be used by the GPS between WAAS

and RTCM (beacon correction).

Navigation Speed : Sets the Navigation Speed among Low Speed, Medium Speed and High Speed.

Autopilot Connection

Connect the Autopilot to the serial Port 1, 2 or 3 (CM 11CV+/11CVS+: it is

possible to select the Port 4 and 5 too).

[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 1/2/3

(CM 11CV+/11CVS+: ports 4/5 too) Output" + [ENTER]

Then choose your preferred setting among the NMEA available settings NMEA

0183 4800-N81-N, NMEA 0180, NMEA 0180/CDX and press [ENTER] to confirm.

External NMEA Connection

Connect the External NMEA to the serial Port 1, 2 or 3 (CM 11CV+/11CVS+: it is

possible to select the Port 4 and 5 too).

[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 1/2/3

(CM 11CV+/11CVS+: ports 4/5 too) Input" + [ENTER]

Then choose your preferred setting among the NMEA available settings NMEA

1200-N81-N, NMEA 4800-N81-N, NMEA 4800-N82-N, NMEA 9600-O81-N, NMEA

9600-N81-N and press [ENTER] to confirm.

C-COM GSM PLUS Connection

[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 1 In-

put" + [ENTER] + "C-COM" + [ENTER]

The modem C-COM can be connected also to the Port 2, 3 (CM 11CV+/11CVS+:

it is possible to select the Port 4 and 5 too), in this case select the format on the

used port.

NOTE The connection is valid for the C-COM IR and C-COM RS232 too.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Interphase CHART MASTER V6 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info