Bedienungsanleitung Intex 604G Krystal Clear filterpomp (Seite 9 von 12) (Englisch)

587278

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

58GS

SAVE THESE INSTRUCTIONS

(58GS) MODEL 604G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/04/2016

English

Page 9

Before emptying your pool for long term storage, or relocation, be sure the water is directed

towards an acceptable drain water receptacle away from the house. Check local regulations

for specific directions regarding disposal of swimming pool water.

Now, drain the pool.

When the pool is empty, disconnect all pool hoses

(8)

from the pool and filter pump, simply

reverse the set up instructions.

Remove the filter cartridge as shown in the Filter Cartridge Cleaning section, steps 2 thru 4.

Remove the nozzle and strainer unoins from the pool wall. Place the wall plugs into the

hose connections. Loosen clamps

(7)

securing the strainer connectors

(9)

before removal.

Drain water from the filter pump housing.

Leave filter pump pieces and hoses outside to thoroughly air dry.

Depending on the cartridge

(5)

usage, a new cartridge may be needed for next season,

keep a spare available.

Cover the seal

(4)

, air release valve O-ring

(2)

and hose seals

(6)

with petroleum jelly to

preserve its resilience during storage.

10.

Store the unit and accessories in a dry place. The storage's temperature should be

controlled, between 32 degrees Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit

(40 degrees Celsius) storage location.

11.

The original packing can be used for storage.

LONG TERM STORAGE

It is recommended that the filter cartridge be replaced at least every 2

weeks. Regularly monitor the filter clogging level.

Make sure the transformer power cord is not plugged into the electrical socket.

To prevent water from escaping the pool, unscrew the pool inlet nozzle

(10)

and strainer

grid

(11)

from the strainer connectors and insert the hat-like plugs into the strainer

connectors.

In a counter-clockwise motion, remove the filter housing collar

(13)

and threaded cover

(3)

Be careful not to lose the cover seal

(4)

Remove filter cartridge

(5)

to clean it. The filter may be cleaned from the spray from a water

hose.

Use judgement as to whether cartridge needs to be replaced. Only use the original Intex

cartridge for replacement. See “Parts Reference” section for detail.

Return cartridge to filtering position.

Return the seal

(4)

and threaded cover

(3)

to their original positions and in a clockwise

direction rescrew the housing collar

(13)

onto the filter housing.

After service, open the air release valve, remove the plugs, allow any air to escape through

the valve before tightening the valve again and replace the pool inlet nozzle

(10)

and

strainer grid

(11)

. The pump is now primed with water again and may be turned on.

Check the inlet and outlet openings regularly to ensure they are not obstructed thus

preventing a good filtration.

10.

The disposal of any used filter media should be in accordance with applicable local

regulation and legislation.

CLEANING OR REPLACING FILTER CARTRIDGES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex 604G Krystal Clear filterpomp Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex 604G Krystal Clear filterpomp

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info