Bedienungsanleitung Intex CS15220 Krystal Clear (Seite 21 von 38) (Englisch)

752504

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

164A

SAVE THESE INSTRUCTIONS Page 21

(164) MODEL CS15220 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2011

English

SALTWATER SYSTEM OPERATION (continued)

OPERATING INSTRUCTIONS

6.Boost cycle

•If the test result is below 0.1ppm, press and hold “BOOST”

button for 5 seconds until the indicator lights up and the

LED display display “80”. This indicates that the saltwater

system has started copper ion and more chlorine sanitizer

production. You can press and hold the “BOOST” button for

another 5 seconds until the indicator is off, which will cancel

the Boost cycle.

Note: Once the system has started copper ion and more

chlorine sanitizer production, the boost button canʼt be re-set until the power

switch is off.

•The boost operating hours is 4 times the amount of time programmed into the

system, i.e. if your saltwater system operating time is 2 hours, the boost procedure

will run 4 x 2 = 8 hours. After boost procedure has been completed, the system

will automatically switch to the normal working mode.

•After a heavy rain or if the pool is dirty, press the “BOOST” button to shock the

pool again.

7.Test pool water regularly:

Once the copper level appears to be balanced, test the pool water every week

to maintain the proper sanitizer level.

Itʼs very important that the free chlorine is between 0.4-1.5 ppm and copper

ion concentration is between 0.1~0.2 ppm. When the copper level is below 0.1

ppm, repeat step 6.

NOTE: A High copper ion concentration may cause blonde hair to exhibit a

green hair. To prevent this, wear a swimming cap during swimming, and wash

hair with special shampoo after using the pool.

See “Troubleshooting Guide”.

8. Stand-by/power saving mode:

•When the cycle ends, the green “SLEEP” indicator on the

control panel lights up and the LED display flashes “93”.

The system is now in Stand-By mode. After a while, it

shuts down and sets itself in a Power Saving mode. The

system will automatically turn itself back on in 24 hours,

starting its daily cycle of chlorine production.

•The “SLEEP” indicator stays on, while the system is in the

Power Saving mode. The LED display however, goes blank

after 1 hour. Press any button ( or ) to view the last LED

code.

9. Running the pump alone without the Saltwater System:

To run the pump alone without the Saltwater System function,

press and hold both ( ) and ( ) buttons for 5 seconds

until you hear a “beep” and the LED display shows “FP”.

The pump is now operating alone. To stop the pump,

manually turn the switch OFF. NOTE: The pump cannot

be operated alone under an automatic timer mode.

IMPORTANT: To keep the initial automatic operating cycle

setting of the Saltwater System, turn the switch ON, the

LED display shows “FP”, then unlock and lock the keypad

controls again, see previous steps 2 and 3. The LED display

shows the initial input hours and the Saltwater System cycle repeats again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex CS15220 Krystal Clear Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex CS15220 Krystal Clear

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info