752350
13
Zoom out
Zoom in
Vorherige Seite
1/33
Nächste Seite
(189IO) MODEL CS7221/CS7231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/11/2012
189A
SAVE THESE INSTRUCTIONS
(Generic layout of an electrical device relative to a swimming pool. Illustration not to scale)
According to the International Standard, IEC 60364-7-702, on electrical installation of swimming pools
and other basins equipments, the following installation distances must be respected:
The filter pump must be position more than 2m away from the pool walls.
The power cord plug to the 220-240 volt electrical power source of the filter pump must be position
more than 3.5 m away from the pool walls.
Check your local authorities to determine the appropriate standard and requirements for “electrical
installation of swimming pools and basins equipments”. The following table is for reference only:
English
Page 13
SETUP INSTRUCTIONS
SALTWATER SYSTEM/FILTER PUMP
Saltwater System/Filter Pump
1. Remove the Saltwater System/Filter Pump and hoses from the packaging.
2. Place the Saltwater System/Filter Pump in a location for hose (8) connections to the plunger valve
assemblies.
NOTE: Some regional regulations may require the filter pump to be mounted on a stationary
platform. There are two mounting holes located in the pump base for this reason. Consult
your local authorities for filter pump mounting requirements.
3. Grasp the two pump hoses (8) and connect the hose nuts to the Saltwater System/Filter Pump.
4. In a counter-clockwise motion unscrew the threaded filter housing collar (3) from the filter housing.
Place it in a safe place.
5. The Saltwater System/Filter Pump is an airtight system. In a counter-clockwise motion turn both air
release valves (1 & 7) 1 - 2 turns to open. DO NOT remove air release valves as water will expel
with force if the motor is turned on and injury may occur.
6. Grasp and remove the filter housing cover (4). Check to see if a cartridge is inside the housing. If
yes, replace the cover, finger tighten the housing collar (3) back onto the filter housing.
7. Gently finger tighten the sediment release valve located at the bottom of the housing to be sure that
water does not leak out.
8. When the pool is filled connect the hose from the electrolytic cell outlet to the highest strainer
assembly. You will find the hose connection at the bottom of the plunger valve assembly. Use the
hose nut to attach the hose.
9. Connect the second hose to the middle of the motor housing and to the remaining liner connection.
IMPORTANT
To prevent air lock, open the lower plunger valve (connected inlet hose) first and then the
upper plunger valve (connected outlet hose). Open air release valves, lift and lower the inlet
hose until water starts to flow out of the air release valves, close air release valves.
FILTER PUMP INSTALLATION DISTANCE
International
France
Germany
The Netherlands
Country/Region Standard Number
IEC 60364-7-702
NF C 15-100-7-702
DIN VDE 0100-702
NEN 1010-702
>2m
>3.5m
POOL
hoses Electrical
device
Downloaded from www.Manualslib.com manuals search engine
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Intex CS7221 Krystal Clear wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Intex CS7221 Krystal Clear

Intex CS7221 Krystal Clear Bedienungsanleitung - Deutsch - 33 seiten

Intex CS7221 Krystal Clear Bedienungsanleitung - Holländisch - 34 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info